Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
PRINTED IN CHINA H0603 18V Cordless Drill and Saw -2 SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. It may also be used to alert against unsafe practices. This symbol is used to alert the user to useful informationNOTICE about proper operation of the equipment. Safety Instructions For Power Tools 1. KEEP ALL SAFETY DEVICES IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning on. 3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 4. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations, or where any flammable or noxious fumes may exist. Keep work area well lighted. 5. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area. 6. MAKE WORK SHOP CHILD PROOF with padlocks, master switches, or by removing starter keys. 7. DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed. 8. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed. H0603 18V Cordless Drill and Saw -1 Safety Instructions For Power Tools 9. USE PROPER EXTENSION CORD 14. MAINTAIN TOOLS WITH CARE. for the charger. Make sure your Keep tools sharp and clean for best extension cord is in good condition. and safest performance. Follow Conductor size should be in accor-instructions for lubricating and dance with the chart below. The changing accessories. amperage rating should be listed on 15. DISCONNECT TOOLS before serthe motor or tool nameplate. An vicing and changing accessories, undersized cord will cause a drop in such as blades, bits, cutters, and line voltage resulting in loss of power the like. and overheating. Your extension 16. REDUCE THE RISK OF UNINTEN- cord must also contain a ground wire TIONAL STARTING. Make sure and plug pin. Always repair or switch is in off position before plug- replace extension cords if they ging in. become damaged. 17. USE RECOMMENDED ACCES- Minimum Gauge for Extension Cords SORIES. Consult the owner’s man- AMP LENGTH RATING 25ft 50ft 100ft 0-6 18 16 16 7-10 18 16 14 11-12 16 16 14 13-16 14 12 12 17-20 12 12 10 21-30 10 10 No ual for recommended accessories. The use of improper accessories may cause risk of injury. 18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate proper ly and perform its intended function. 10. WEAR PROPER APPAREL. Do not Check for alignment of moving wear loose clothing, gloves, neck- parts, binding of moving parts, ties, rings, bracelets, or other jewel- breakage of parts, mounting, and ry which may get caught in moving any other conditions that may affect parts. Non-slip footwear is recom its operation. A guard or other part mended. Wear protective hair cover- that is damaged should be properly ing to contain long hair. repaired or replaced. 11. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eye glasses only have impact resistant lenses, they are NOT safety glass- No list of safety guidelines can be complete. Every shop environment is es. different. Always consider safety 12. SECURE WORK. Use clamps or a first, as it applies to your individual vise to hold work when practical. It’s working conditions. Use this and safer than using your hand and frees other machinery with caution and both hands to operate tool. respect. Failure to do so could result 13. DON’T OVERREACH. Keep proper in serious personal injury, damage to footing and balance at all times. equipment or poor work results. -2- H0603 18V Cordless Drill and Saw ADDITIONAL SAFETY 1. Remove battery pack before area. Never reach under workpiece changing blade, adjusting or serwhile blade is in motion. vicing trim saw. 4. Know how to avoid kick-back. 2. Keep guards in place and main-Kick-back occurs when blade tained in good working order. begins to stall causing the saw to be Never secure blade guard open. Do propelled at the operator. not use trim saw if blade does not 5. Never saw into a wall or work- return so that blade is completely covered. piece without...