Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
Finally, rotate the sleeve to the left, and it will loosen. 5. Automatic spindle-lock mechanism This unit has automatic spindle-lock mechanism for quick bit changes. 6. Confirm that the battery is mounted correctly 7. Check the rotational direction The bit rotates clockwise (viewed from the rear side) Trigger by pushing the R-side of the selector button. switch The L-side of the selector button is pushed to turn the bit counterclockwise. (See Fig. 19) (The L and R marks are provided on the selector button.) . When the trigger switch is depressed, the tool rotates. When the trigger is released, the tool stops. . The rotational speed of the drill can be controlled by R L varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the trigger switch is pulled more. Selector . When releasing the trigger of the switch, the brake Button will be applied for immediate stopping. Fig. 19 8. Change rotation speed Shift knob Shift knob High speed Low speed Fig. 20 Fig. 21 English 24 Operate the shift knob to change the rotational speed. Move the shift knob in the direction of the arrow. (See Fig. 20 and 21) When the shift knob is set to “LOW”, the drill rotates at a low speed. When set to “HIGH”, the drill rotates at a high speed. CAUTION: When changing the rotational speed with the shift knob, confirm that the switch is off. Changing the speed while the motor is rotating will damage the gears. When a large force is required for operation (operations indicated in the following chart) set the shift knob to “LOW”. If “HIGH” is set and the unit is used, it may cause the motor to burn out or malfunction prematurely. 9. Confirm the cap position (See Fig. 22) The tightening torque of this unit can be adjusted according to the cap position, at which the cap is set. (1) When using this unit as a screwdriver, line up the one of the numbers “1, 4, 7 ... 22” on the cap, or the black dot, with the triangle mark on the outer body. (2) When using this unit as a drill, line up the cap drill mark “ ” with the triangle mark on the outer body. CAUTION: The cap cannot be set between the numerals “1, 4, 7 ... 22” or the black dot. Do not use with the cap numeral at “22” and the black line at the middle of the drill mark. Doing so may cause damage. (See Fig. 23) 10. Tightening torque adjustment (1) Tightening torque Tightening torque should correspond in its intensity to the screw diameter. When too strong power is used, the screw head may be broken or be injured. Be sure to adjust the cap position according to the screw diameter. Model DS14DMR DS18DMR Metal Drilling Wood Drilling Wood Screw Tightening When the diameter of the hole exceeds 15/16" (24 mm). When the size of the wood screw exceeds 3/16" (4.8 mm) diameter . 2" (50 mm). When the diameter of the hole exceeds 1-1/16" (27 mm). Fig. 22 Drill mark Fig. 23 Drill mark Triangle mark Black line When the diameter of the hole exceeds 5/16" (8 mm). Triangle mark Cap English (2) Tightening torque indication (See Fig. 22) The tightening torque differs depending on the type of screw and the material being tightened. The unit indicates the tightening torque with the numbers “1, 4, 7 ... 22” on the cap, and a black dot. The tightening torque at position “1” is the weakest and the torque is strongest at the highest number. (3) Adjusting the tightening torque (See Fig. 22) Rotate the cap and line up the numbers “1, 4, 7 ... 22” on the cap, or the black dot, with the triangle mark on the outer body. Adjust the cap in the weak or the strong torque direction according to the torque you need. CAUTION: . The motor rotation may be locked to cease while the unit is used as drill. While operating the driver drill, take care not to lock the motor. . When setting the shift knob to “HIGH” (high speed) and the position of the cap is between “16” and “22”, it may happen that the clutch does not engaged and that the motor is locked. In such a case, please set the shift knob to “LOW” (low speed). . If the motor is locked, immediately turn the power off. If the motor is locked for a while, the motor or battery may be burnt. . Too long hammering may cause the screw broken due to excessive tightening. . A buzzing noise is produced when the motor is about to rotate; this is only a noise, not a machine failure. THE SCOPE AND SUGGESTIONS FOR USES Table 6 Work Cap position Suggestions Drilling Wood Use for drilling purpose.Steel Aluminum Screw tightening Small screw 1 – 22 Use the bit and socket matching the screw diameter. Wood screw 1 – Use after drilling a pilot hole. English HOW TO SELECT TIGHTENING TORQUE Table 7 Cap position Tightening torque Operation example 1 Approximately 18 in-lbs. (20 kg-cm) Machine screw tightening. Screw tightening for soft wood material. 4 Approximately 27 in-lbs. (31 kg-cm) 7 Approximately 37 in-lbs. (43 kg-cm) 10 Approximately 47 in-lbs. (54 kg-cm) Screw tightening for hard wood material.16 Approximately 67 in-lbs....
Ce manuel est également adapté pour les modèles :Perceuses et shuropopverty - DS 18DMR (2.02 mb)