Évaluations - 2, GPA: 3
(
)
)
|
Facilité d'utilisation
Daily - Air Supply Maintenance: 1. Every day, perform maintenance on the air supply according to the component manufacturers’ instructions. The lubricator’s oil level needs to be maintained and the moisture filter must be regularly drained. Performing routine maintenance on the air supply will allow the tool to operate more safely and will also reduce wear on the tool. Quarterly (every 3 months) - Tool 2. Disassembly, Cleaning, and Inspection: Have the internal mechanism cleaned, inspected, and lubricated by a qualified technician. If the vanes need replacement, all vanes should be replaced as a set. Troubleshooting Problem Possible Causes Likely Solutions Decreased output. Not enough air pressure and/1. or air flow. Obstructed trigger. 2. Incorrect lubrication or not 3. enough lubrication. Blocked air inlet screen (if 4. equipped). Air leaking from loose housing. 5. Mechanism contaminated. 6. Vane wear or damage.7. Check for loose connections and make sure 1. air supply is providing enough air flow (CFM) at required pressure (PSI) to tool’s air inlet. Do not exceed maximum air pressure. Clean around trigger to ensure free 2. movement. Lubricate using air tool oil and grease 3. according to directions. Clean air inlet screen of buildup. 4. Make sure housing is properly assembled 5. and tight. Have qualified technician clean and lubricate 6. mechanism. Install in-line filter in air supply as stated in Initial Set Up: Air Supply. Replace all vanes.7. Housing heats during use. Incorrect lubrication or not 1. enough lubrication. Worn parts.2. Lubricate using air tool oil and grease 1. according to directions. Have qualified technician inspect internal 2. mechanism and replace parts as needed. Severe air leakage. (Slight air leakage is normal, especially on older tools.) Cross-threaded housing 1. components. Loose housing. 2. Damaged valve or housing.3. Dirty, worn or damaged valve. 4. Check for incorrect alignment and uneven 1. gaps. If cross-threaded, disassemble and replace damaged parts before use. Tighten housing assembly. If housing cannot 2. tighten properly, internal parts may be misaligned. Replace damaged components.3. Clean or replace valve assembly.4. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect air supply before service. 65159 PARTS LIST Part Description Q’ty 1 Air Inlet 1 2 O-Ring 1 3 Exhaust Deflector 1 4 O-Ring 1 5 Motor Housing 1 6 Air Regulator 1 7 Spring Pin 2 8 O-Ring 1 9 Throttle Valve Spring 1 10 Throttle Valve Stem 1 11 O-Ring 1 12 O-Ring 1 13 Power Regulator 1 14 O-Ring 3 15 Ball Bearing 1 16 Rear End Plate 1 17 Cylinder 1 18 Rotor 1 19 Rotor Blade 4 20 Front End Plate 1 21 Ball Bearing 1 22 Ring Gear 1 23 Work Spindle (Including Work Spindle Pin) 1 25 Planet Gear 3 26 Coupling Nut 1 65159 PARTS LIST Part Description Q’ty 27 Needle Bearing 1 28 Bushing 1 29 Spacer 2 30A Ratchet Housing (Including Grease Fitting) 1 31 Crank Shaft 1 32 Drive Bushing 1 33 Ratchet Yoke 1 34 Ratchet Housing Cover 1 35A Forward/Reverse Lever (Including Grease Fitting) 1 36 Lock Washer 1 37 Spring Pin 1 38 Anvil (Including Steel Ball Spring, Steel Ball) 1 41 Lock Spring 1 42 Lock Pin 1 43 Ratchet Pawl 1 44 Ratchet Pawl Pin 1 45 Thrust Spacer 1 46 Thrust Washer 1 47 Retainer 1 48 Trigger 1 49 Trigger Pin 1 50 Housing Cover 1 51 Retainer 1 PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/ or distributor expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out of his or her installation of replacement parts thereto. 65159 ASSEMBLY DIAGRAM Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. 65160 PARTS LIST Part Description Q’ty 1 Air Inlet 1 2 O-Ring 1 3 Throttle Valve Spring 1 4B Throttle Valve Assembly (Includes Throttle Valve Rubber and Throttle Valve Pin) 1 5 O-Ring 1 6 Throttle Valve Seat 1 7 Spring Pin 1 8 Motor Housing 1 9 Air Regulator 1 10 O-Ring 1 11 Spring Pin 1 12 Throttle Valve Stem 1 13 Trigger Spring 1 14 Trigger 1 15 Spring Pin 1 16 O-Ring 1 17 Exhaust Deflector 1 18 Bearing Cap 1 19 Ball Bearing 4 20 Rear End Plate 1 21 Spring Pin 1 22 Cylinder 1 23 Rotor 1 24 Rotor Blade 4 25 O-Ring 1 26 Front End Plate 1 27 Ball Bearing 1 65160 PARTS LIST Part Description Q’ty 27-1 Ball Bearin...
Ce manuel est également adapté pour les modèles :Perceuses et shuropopverty - 65159 (559.7 kb)
Perceuses et shuropopverty - 65161 (559.7 kb)