Évaluations - 4, GPA: 4.5
(
)
)
|
Facilité d'utilisation
Leave the screwdriver in place. 5. Tighten the (inner) Hex Nut just enough to engage the notch. If this Hex Nut is too tight, it will restrict (up and down) Chuck-Spindle movement. 6. Pull the Feed Knob and check the spring tension, making sure the up movement is smooth and complete. From one inch down, the Chuck should return to its uppermost position. If more tension is required, repeat steps. 7. Replace the (outer) Hex Nut (7) and tighten on top of the (inner) Hex Nut. Do not overtighten. 8. If the (up/down) movement is restricted, slightly loosen the (inner) Hex Nut, and retighten the (outer) Hex Nut. General Maintenance 1. Using compressed air, blow clean the Table, Base, and Motor cooling vents of dirt and materials. 2. Apply paste wax to the Table and Column to enable movement and to help keep surfaces clean. 3. All bearings are factory lubricated and need no further attention. 4. Periodically, lubricate the Tube Column, Table, and Spindle upper teeth with a light oil. 5. Monthly, check the tightness of all mounting screws and bolts in the Base, Column, and Head assemblies. 6. Check belt for wear and replace if frayed or damaged in any way. 7. Lubricate Spindle assembly with a light oil, weekly. 8. Store in a clean and dry location. Cap Spring (8) Hex Nut (7) Guide Pin (16) Clamping Lever (30), Left Troubleshooting syMptoMpossible causesolutionDrill bit burns orsmokes- Incorrect spindle speed- Dull drill bit- Drilling too slowly- Lacking lubrication- Change spindle speed- Replace with new bit- Drill faster- Lubricate cutting areaMakes unusualnoise- Belt tension set wrong- Spindle dry- Loose spindle pulley- Loose motor pulley- Adjust belt tension- Lubricate spindle- Check pulley nut- Tighten Set screwsDrill bit wobbles- Bent bit- Worn Spindle Bearings- Drill bit not in Chuck correctly- Chuck not properly installed- Replace drill bit- Replace spindle bearings- Reinstall drill bit- Reinstall Chuck and Arbor assemblyFeed Wheelreturns slowly, ortoo fast- Tension Spring not in adjustment- Adjust Tension Spring. See page 9. Drill bit binds- Workpiece pinching drill bit- Dull drill bit- Feed pressure too hard- Belts loose- Reposition workpiece, lubricate drill- Replace drill bit- Pull Feed Handle slowly. - Adjust motor and spindle belt tension NOTE: Some parts are listed in these Part Lists are shown for illustration purposes only and are not available individually as replacement parts. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. item #description1Self-tapping Screw, 4.22No-Volt Switch3Screw, Pan Hd., M5x124Switch Box5Screw Set, Special6Nut, Hex7Nut, Hex, M128Cap Spring9Spring, Torsion10Retainer Spring11Seat Spring12Roll Pin13Screw, Socket Hd. 14Head15Locking Shoe16Guide Pin17Retaining Ring18Column Guide19Horizontal Tube20Cover Mount item #description21Motor Mount22Motor23Nut, Hex, M824Washer, 825Cord, Motor26Washer, 827Screw, Hex, M8x2028Nut, Thumb29Cord, Power30Clamping Lever31Horizontal Rack32Moving Bar33Scale34Feed Knob35Feed Rod36Hub37Ring, Depth Stop38Depth Lock Screw39Pin Stop Head Assembly Drawing Head Assembly Parts List Pulley and Spindle Assembly Parts List item #descriptionA1V-belt, M58A2Pulley NutA3Spindle PulleyA4Insert PulleyA5Retaining RingA6Locking RingA7WasherA8Ball Bearing, 60203A9Washer, RubberA10Quill TubeA11Chuck KeyA12ChuckA13Arbor item #descriptionA14Drift KeyA15SpindleA16Ball Bearing, 60204A17KnobA18Screw, M5x12A19Screw, M5x12A20Clamp CordA21Screw, M6x12A23Motor PulleyA24Screw, M6x10A25Belt GuardA26Form Washer Pulley and Spindle Assembly Drawing When ordering a part from this drawing, add an “A” prefix to the part number. Base and Table Assembly Parts List item #descriptionB1ColumnB2RackB3Screw, M10x12B4Column SupportB5Hex Bolt, M10x40B6BaseB7Table SupportB8CrankB10Pin GearB11Screw, M6x10B12Hex Bolt, M16x35B13Table ClampB14ArmB15Extend ArmB16Support ClampB17Gear, HelicalB18Worm, ElevationB19Column CollarB20TableB21Wire Stabilizer Base and Table Assembly Drawing When ordering a part from this drawing, add an “B” prefix to the part number. Limited 1 year / 90 Day warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase tha...