Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
Repair any leaks found. 9. If the tool will not be used at this time, turn off and detach the air supply, safely discharge any residual air pressure, and release the throttle and/or turn the switch to its off position to prevent accidental operation. 10. Drain the compressor regularly. Note: Residual air pressure should not be present after the tool is disconnected from the air supply. However, it is a good safety measure to attempt to discharge the tool in a safe fashion after disconnecting to ensure that the tool is disconnected and unpowered. Assembly 1. While main body of Impact Wrench does come assembled, the Side Handle (45) needs to be fastened to the side of Hammer Case (43). 2. Attach Washers (46A) to Screws (46). Position Handle (45) against Hammer Case, attach Screws and then securely tighten. OPERATING INSTRUCTIONS Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found, do not use tool until repaired. Tool Set Up TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release Trigger before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY: Do not adjust or tamper with any control or component in a way not specifically explained within this manual. Improper adjustment can result in tool failure or other serious hazards. Work Piece and Work Area Set Up 1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent distraction and injury. 2. Route the air hose along a safe route to reach the work area without creating a tripping hazard or exposing the air hose to possible damage. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. 3. There must not be hazardous objects (such as utility lines or foreign objects) nearby that will present a hazard while working. General Operating Instructions 1. WARNING! Use only 1” Drive Impact type sockets (sold separately). 2. WARNING! The Impact Wrench is heavy and supplies powerful amounts of torque and should be operated with BOTH hands. Failure to do so can lead to personal injury or property damage. 3. If an automatic oiler is not used, add a few drops of Pneumatic Tool Oil to the airline connection before use. Add a few drops more after each hour of continual use. 4. Push and snap the socket (not included) onto the Anvil (38). 5. The Direction Valve (17) has three forward and three reverse speed settings Turn Direction Valve to the right toward the Trigger Handle (1) to tighten. See Figure 1, below. 6. Place the socket over the nut you wish to tighten. 7. Grip tool firmly with BOTH hands and gently squeeze Trigger (13). 8. Adjust air flow by turning Air Regulator Knob from positions 1 through 3. Position 1 allows the lowest amount of air flow, and Position 3 the highest. 9. If the tool requires more force to accomplish task, verify that the tool receives sufficient, unobstructed airflow (CFM) and increase the pressure (PSI) output of the regulator up to the maximum air pressure rating of this tool. CAUTION! TO PREVENT TOOL AND ACCESSORY FAILURE, RESULTING IN INJURY: Do not exceed the tool’s maximum air pressure rating. If the tool still does not have sufficient force at maximum pressure and sufficient airflow, then a larger tool may be required. 10. Once nut is tightened, release Trigger. Turn off the air supply and disconnect the hose. 11. If available, check the recommended torque specification for the nut. Use a torque wrench to tighten the nut to the proper setting after using the Impact Wrench. 12. To set Impact Wrench in Reverse, slide Direction Valve to the left and away from the Trigger Handle for counterclockwise (reverse) rotation. 13. WARNING! Before changing the rotational direction of the tool, release the Trigger and allow Tool to come to a complete stop. 14. Adjust air flow by turning Air Regulator Knob from positions 1 Forward Setting Figure 1 Reverse Setting To Trigger Handle (1) Direction Valve (17) Please Note: Figure 1 (view from side of tool) shows Settings above Direction Valve without protective black coating. through 3. Position 1 allows the lowest amount of air flow, and Position 3 the highest. 15. When the nut is loosened, release Trigger. Turn off air compressor and disconnect the hose. If needed, remove the nut from the socket. 16. To prevent accidents, turn off tool, detach air supply, safely discharge any residual air pressure in the tool, and release the throttle and/or turn the switch to its off position after use. Clean external surfaces of the tool with clean, dry cloth, and apply a thin coat of tool oil. Then store the tool indoors out of children’s reach. US...