Évaluations - 2, GPA: 4.5
(
)
)
|
Facilité d'utilisation
Do not use the tool if any switch does not turn On and Off properly. 16. Guard against electric shock. Prevent body contact with electrical circuits when using this tool. SKU 91332 Page 3 17. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. 18. Do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 19. Maintenance. For your safety, service and maintenance should be performed regularly by a qualified technician. 20. People with pacemakers should consult their physician(s) before using this product. Electromagnetic fields in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker. In addition, people with pacemakers should adhere to the following: ¦ Avoid operating power tools alone. ¦ Don’t use a power tool with the power switch locked on. ¦ Properly maintain and inspect all tools before use to avoid electrical shock. Note: Performance of this tool may vary depending on variations in battery power. Warning:The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure the that all following parts are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. Cordless Screwdriver Charger Adapter Accessory Bits and Adapters SKU 91332 Page 4 Operation Operation 1. To avoid accidents, only charge the supplied batteries. Do not use a different charger adapter with this tool. 2. Do not expose the battery to rain or wet conditions. 3. To avoid damage of cable and plug, never pull the cable to disconnect the charger. 4. Do not charge the battery if either the cable or plug are damaged. 5. Repairs should be carried out by a qualified technician only. 6. Do not touch the battery poles with any conductive source. 7. Do not store the battery in a box with other metal objects. 8. Do not throw the battery in a fire. Charging the Battery The internal Battery does not come charged from the factory. Charge before using. 1. Insert the Charger Adapter module plug into the unit connector as shown below. Note: Never over-discharge a battery by using the tool even after tool performance is decreasing. Severe heat is most destructive to a battery; the more heat generated, the faster the battery loses power. A battery that gets too hot can be permanently damaged. Never attempt to discharge a tool’s battery by continuing to pull the tool trigger. When tool performance begins to diminish, stop the tool and re-charge the battery for optimal performance. 2. Plug the Charger Adapter module into an electrical outlet. The red LED on the cordless Screwdriver will light. Charge the new battery from 5 to 7 hours. Battery usage time will ramp up as the new Battery is used, and recharged. Do not overcharge the battery. Caution: Never charge Battery for more than 7 hours continuously. Charger Adapter should not be left plugged in or charging for more than 7 hours. SKU 91332 Page 5 3. Remove the Power Adapter from the electrical outlet and store in the Blowmold case. Using the Cordless Screwdriver 1. Set the Screwdriver handle grip style by pressing on the Grip Button Lock and turning the handle for pistol or straight grip. Pistol Grip Straight Grip Rocker Switch (Forward / Reverse) Grip Button Lock Accessory Bit, Driver, or Adapter Accessory Bit, Driver, or Adapter Chuck (1) Chuck (1) 2. Insert the desired bit, driver, or adapter into the Chuck (1). 3. Engage the bit, driver, or adapter over the item being turned. 4. Press forward on the Rocker Switch for turning clockwise. 5. Press backward on the Rocker Switch for turning counterclockwise. Maintenance 1. When finished using the Screwdriver, place it in the Blowmold case along with all the accessories. 2. Store in a clean and dry location. 3. Recharge the batteries once a month whether used or not. SKU 91332 Page 6 Parts List Parts List 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. Description Chuck Screwnail Screwnail Enclosure (A) Screwnail Enclosure (right) Switch Limit Block Bearing Limit Box Enclosure (B) Heat-loss Block Gear Steering Stem Gear Gear Motor Enclosure (left) Battery Charger Adapter NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED TH...