Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
Place the point of the bit in the indentation and start drilling. Use a cutting lubricant when drilling metals. The exceptions are iron and brass which should be drilled dry. CAUTION : *Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pressure will only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool. *There is a tremendous force exerted on the tool/bit at the time of hole breakthrough. Hold t h e tool firmly and exert care when the bit begins to break through the workpiece. 0 A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. However, the tool may back out abruptly if you do not hold it firmly. 0 Always secure small workpieces in a vise or similar hold-down device. Nominal diameter of wood screw (mm) Screwdriving operation Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool. Release the switch trigger just as the screw bottoms out. The electric brake will then stop the tool immediately, preventing the screw and/or bit from being damaged. NOTE : *Make sure that the driver bit is inserted straight in the screw head, or the screw and/or Recommended size of Dilot hole 1mml bit may be damaged. When driving wood screws, predrill pilot holes to make driving easier and to prevent splitting of the workpiece. See the chart. 2.0 - 2.2 3.1 (118“l I (5/64,, - 3/32,,) 2.2 - 2.5 13/32” - 3/32”) 3.5 (9/64”) 2.5 - 2.8 3.8 (5132”) 1 13/32,, - 7,64,,1 2.9 - 3.2 4 . 5 ( 1 1/64”] I 17/64,, - 1/8,,1 8 MAINTENANCE CAUTION : Always be sure that the tool is switched off before attempting to perform inspection or maintenance. To remove the cover, push it in the direction of the arrow while pressing down on the "OPEN" portion of the cover. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ' DISPOSING OF TOOL A nicad battery is built into the handle of this tool. Always remove it before disposing of the tool. Removing built-in battery CAUTION : Never remove the built-in battery from the tool except when disposing of the tool. The battery will be damaged or a battery short-circuit could result. Withdraw the built-in battery halfway. Disconnect the two lead wires from the battery by pulling them from the battery terminals. Then withdraw the battery completely. To prevent a battery short-circuit, tape the battery terminals or put the battery into a plastics bag. (Note: Never put two or more batteries into one plastics bag. Battery shortcircuit may result.) CAUTION : Never incinerate the battery even if it is severely damaged or is completely worn out. It can explode in a fire or toxic materials can leak out of it. 9 Recycling the battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. To recycle the battery: 1 . Remove the battery from the tool. 2. (a) Take the battery to your nearest Makita Factory Service Center. or (b) Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location. Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling. See your local yellow pages under “Tools - Electric. Ni-Cd 10 OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The u s e of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in t h e proper and intended manner. Bit 1 Size 1 Part NO. Phillips I # 2 I 784214-0A 1 1 #3 I 784215-0A !- Rubber pad assembly Part No. 123001 -2 Slotted - Foam polishing pad Part No. 743023-2 Square drill bit - Quick charger (A.C. only) Model DC7020B Wool bonnet Part No. 743401-6 Plastic carrying case Part No. 824417-1 11 Jan -14-’93 U S 10 mm (3/8”) CORDLESS DRILL Model 6076D Note: The switch and other part configurations may differ from country to country. 12 MODEL 6076D ,&, DESCRIPTION 1 0 Jan -14-'93 US ""0" SDDE SCRIPTION 1 1 2 1 3 1 4 1 5 1 6 1 1 1 8 1 1 I Tapping Screw M3x20 Name Plate Housing Set IWith Item 171 Cwunleraunh Her Soohel Scmw M5r21 Keyless Drill Chuck Gear DC Motor 7 2 V Circuit Board Plane Bearing 5 MACHINE 17 1 1 8 I 1 Batter" Switch Plane Bearing 3 Gear COmDlete 13-58 Plane Bearing 3 Holder 6 Housing Set IWith Item 31 C0"CX Note The switch and other part specifications may differ from cnuntry to country 13 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and t...
Ce manuel est également adapté pour les modèles :Perceuses et shuropopverty - 60761 (1.21 mb)