Évaluations - 3, GPA: 5
(
)
)
|
Facilité d'utilisation
The battery cartridge can explode in a fire. ADDITIONAL SAFETY RULES FOR CORDLESS DRIVER DRILL 1. Be aware that this tool is always in an operating condition, because it does not have to be plugged into an electrical outlet. 2. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. 3.Hold the tool firmly. 4.Keep hands away from rotating parts. 5. When drilling into walls, floors or wherever "live" electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by the insulated grasping surfaces to prevent electric shock if you drill into a "live" wire. 6. Do not leave the tool running. Operate the tool only when hand-held. 7. Do not touch the drill bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin. SAVE THESE INSTRUCTIONS. Installing or removing battery cartridge *Always switch off the tool before insertion or removal or the battery cartridge. *To remove the battery cartridge, pull out Battery cartridge the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool. *To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully before using the tool. Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly. Charging Your new battery cartridge is not charged. You will need to charge it before use. Use the fast charger Model DC1201 to charge the battery cartridge. *Plug the fast charger into the proper A/C voltage source. The charging light will flash in green color. *Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the fast charger. Insert the cartridge fully into the port so that it rests on the charger port floor. *When the battery cartridge is inserted, the charging light color will change from green to red and charging will begin. The charging light will remain lit steadily during charging. *When charging is completed, the charging light color will change from red to green and a tone will sound steadily for about 5 seconds. The charging time is approximately one hour. *After charging, unplug the charger from the power source. CAUTION : *The fast charger Model DC1201 is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer’s batteries. *When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharg- ing it completely and recharging a couple of times. 0 If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charg- ing light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you remove the battery cartridge from the fast charger. 0 If the charging light flashes alternately in green and red color and a tone sounds "beep, beep, beep, .. ." for about 20 seconds, a problem exists and charging is not possible. The terminals on the charger or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged. 0 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Installing or removing driver bit or drill bit CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. To install the bit, push the sleeve up to- ward the "FREE" side and turn the sleeve A FREE side counterclockwise while holding the ring with your other hand as illustrated at right. Sleeve LOCK side I Place the bit in the chuck as far as it will go. Hold the ring firmly and turn the sleeve clockwise to tighten the chuck. Then push the sleeve down toward the "LOCK" side. See illustration. To remove the bit, push the sleeve up toward the "FREE" side and turn the sleeve counterclockwise while holding the ring with your other hand. CAUTION : .Do not attempt to turn the sleeve forcibly when the sleeve is in the"L0CK" position. The sleeve may be damaged. .Always push the sleeve down toward the "LOCK" side before operation. If you operate the tool with the sleeve in the "FREE" position, the chuck may loosen and the bit may come out unexpectedly. Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. Switch trigger qy'vi CAUTION : Before inserting the battery cartridge into the tool, always ...
Ce manuel est également adapté pour les modèles :Perceuses et shuropopverty - 6312DWG (834.8 kb)
Perceuses et shuropopverty - 6312D (834.8 kb)