Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
The plug and outlet should look like those in Figure A. Double Insulated Tools: Tools with Two Prong Plugs Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association and the National Electrical Code. Double Insulated tools may be used in either of the 120 volt outlets shown in Figures B and C. Fig. B Fig. C Specifications Maximum Recommended Capacity Drill No Fine Coarse Steel Speed Motor Cat. No. Volts AC Amps Load RPM Chuck or Taper Drill Thread Tap Thread Tap Hawg™Cutters -4253- 1 • 120 6.2 600 1/2" Chuck 5/8" 5/8" - 18 3/8" - 16 - -4262- 1 120 11.5 350 3/4" Chuck 1-3/8" 1" - 14 7/8" - 9 4" ** HIGH4292-1 120 11.5 750 No. 3 M.T. 3/4" - - 2" * LOW- - - 375 - 1-1/4" 1" - 14 7/8" - 9 4" * HIGH4297-1 120 11.5 500 No. 3 M.T. 1-1/8" - - 3" * LOW- - - 250 - 1-1/2" 1" - 14 1" - 8 5" * 4 M.T. - Internal Morse Taper Socket • - 5/8" -11 or 1/2" -13 taps not **- Requires use Cat. No. 49-57-* - Requires use Arbor, Cat. No. 49-5 EXTENSION CORDS Grounded tools require a three wire extension cord. Double insulated tools can use either a two or three wire extension cord. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. Refer to the table shown to determine the required minimum wire size. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. When using more than one extension cord to make up the total length, be sure each cord contains at least the minimum wire size required. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum wire size. Guidelines for Using Extension Cords • If you are using an extension cord outdoors, be sure it is marked with the suffix “W-A” (“W” in Canada) to indicate that it is acceptable for outdoor use. • Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it. • Protect your extension cords from sharp objects, excessive heat and damp or wet areas. Recommended Minimum Wire Gauge for Extension Cords* Nameplate Extension Cord Length Amperes 25' 50' 75' 100' 150' 0 - 2.0 2.1 - 3.4 3.5 - 5.0 5.1 - 7.0 7.1 - 12.0 12.1 - 16.0 16.1 - 20.0 18 18 18 18 16 14 12 18 18 18 16 14 12 10 18 18 16 14 12 10 18 16 14 12 10 16 14 12 12 * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. READ AND SAVE ALL INSTRUCTIONS FOR FUTURE USE. Symbology Underwriters Laboratories, Inc., United States and Canada Double Insulated Volts Alternating Current No Load r...
Ce manuel est également adapté pour les modèles :Perceuses et shuropopverty - 4202 (1.31 mb)
Perceuses et shuropopverty - 4202 (1.31 mb)
Perceuses et shuropopverty - 4206-1 (1.31 mb)
Perceuses et shuropopverty - 4204-1 (1.31 mb)