Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
VEA EL ESPANOL EN LA CONTRAPORTADA. SAVE THIS MANUAL FOR FUTURE REFERENCE. INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA DE GARANTIA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. Catalog # FS100SF, ASF100EX Form No.618492-01, Rev. 2 (Dec. ‘04) Copyright © 2004 Black & Decker Printed in Mexico INSTRUCTION MANUAL Catalog Numbers FS100SF, ASF100EX Scrrew Feederr BEFORE RETURNING THIS PRODUCT FOR ANY REASON PLEASE CALL 1-800-544-6986 IF YOU SHOULD EXPERIENCE APROBLEM WITH YOUR BLACK & DECKER PRODUCT, CALL 1-800-544-6986 BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No., TYPE No., AND DATE CODE. IN MOST CASES, ABLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE ASUGGESTION OR COMMENT, GIVE US ACALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER. 2 3 5 6 4 7 8 9 10 11 12 13 Screw Feeder Diagram 1. Screw Filter 2. Rear Support 3. Front Support 4. Clear Tube 5. Sliding Barrel 6. Main Body Assembly 7. Quick Change Bit Holder 8. Release Tabs 9. Extension Assembly 10. Handle 11. Drive Bit (Phillip/Robertson) Diagramme de l'alimenteur a vis 1. Filtre de vis 2. Support arriere 3. Support avant 4. Tube transparent 5. Canon coulissant 6. Corps principal 7. Porte-embout a changement rapide 8. Languettes de degagement 9. Rallonge 10. Poignee 11. Embout (Phillips/Robertson) Diagrama del alimentador de tornillos 1. Filtro de tornillos 2. Soporte trasero 3. Soporte delantero 4. Tubo transparente 5. Cilindro deslizante 6. Conjunto del cuerpo principal 7. Portabrocas de recambio rapido 8. Lenguetas de liberacion 9. Conjunto de extension 10. Empunadura 11. Broca impulsora (Phillip / Robertson) 2 1 3 7 11 10 9 8 6 5 4 1 15 14 16 1514 16 Assembly Figure 1 -Attach the handle to the extension assembly by turning the handle counterclockwise to loosen the ring adjustment. After attaching the handle assembly, turn the handle clockwise to tighten. Be sure handle is fully seated. Figure 2 -Insert the correct driver bit tip for the screws being used (Phillips / Robertson Head), by placing the bit at the quick-change bit holder and retracting the quick-change barrel. Figure 3 -Insert the bit through the main body as shown, making sure the front assembly hole aligns with the sliding barrel and secure the assembly unit until it clicks into place. Figure 4 -Insert the clear tube through the front and rear supports and into the sliding barrel until it stops, a slight rotational movement can help. Figure 5 -Attach the drill chuck to the hex shank shaft. Changing a Drive Bit Figure 6 -Remove the clear tube from the sliding barrel. Hold the unit as shown, press in the tab and turn in the direction of the arrow to release. Figure 7 -Remove the main body assembly and place it aside. Figure 8 -Press the barrel of the quick-change bit holder and remove the bit, insert the replacement, reverse steps to reinstall. Figure 9 -Reattach the main body assembly making sure to align the clear tube with the sliding barrel. Operation Figure 10 -Check for correct driver bit tip for screws being used by retracting the sliding barrel. (See “Changing A Drive Bit”) Figure 11 -Set depth stop to desired counter sink depth. Figure 12 -Holding the unit vertically, drop screws through the screw filter. Note: Do not overfill the tube as it may jam the screw filter. Figure 13 -Completely depress and release sliding barrel once by pressing onto horizontal surface to load first screw into barrel. Figure 14 -To drive screws, locate tip on workpiece, hold drill and feeder assembly vertically, squeeze trigger while pushing on drill. Stop when ratcheting sound starts (drive bit has disengaged from screw head at set depth.) Always hold unit securely with two hands in a vertical downward position only. Keep hands and feet away from main body assembly when tool is depressed. Note that the weight of some heavier drills is enough to cause tool to depress. To Empty Screws Figure 15 -Always remove screws from tubes by pulling tube from sliding barrel, allowing screws to fall from bare end. DO NOT try to remove screws through the screw filter at other end. Clearing Jammed Screws Figure 16 -To remove screws which have become dislodged, lift the clear plastic window at the head of the sliding barrel. Recommendations • Use of a variable speed drill at medium to low speed. • If the unit tends to vibrate after engaging the drill’s chuck, loosen the chuck jaws and reattach. • Do not use the unit with a hammer drill option engaged. • The feeder accepts a variety of screw types, however, not all of them will work correctly. Experiment by driving screws into scrap material first. • Do not use Trim Head screws. • For best results, use ONLY with drywall and decking type screws number #6 & #8 Phillips or Robertson head, 1.5 to 3 inches in length. • If a screw head has the option to use both Phillips and Robertson (square) bit, then it is recommended to use as a first option the square bit to get the full advantages of the dept...
Ce manuel est également adapté pour les modèles :Perceuses et shuropopverty - 618492-01 (626.88 kb)
Perceuses et shuropopverty - ASF100EX (626.88 kb)