Évaluations - 3, GPA: 3.7 ( )

Fabricant : Milwaukee Taille : 266.12 kb Nom Fichier : Langue d'enseignement:

Driving Screws When driving screws, use the proper screwdriver bit for your job. After drilling pilot and shank holes, start the screw slowly and increase the speed as driving progresses. Set the screw by slowing to a stop. Do not run screws down at excessive speeds. To remove screws, reverse the motor. High rotational force. To reduce the risk of injury, always hold or brace secrely. Always use side handle on tools rated 1200 RPM or less. WARNING! 11 Fig. 13 1. Unplug tool and the cartridge facing Bit Binding A high rotational brush holder screw binds. If the bit binds, pull cartridge out. in the opposite direction 1312 Replacing Brushes (Fig. 15 & 16) MILWAUKEE Magnum Drills have an exclusive Brush Cartridge System. The tool will not start when the brushes are worn to 1/8", preventing expensive damage to the armature. New brushes are provided in the Cartridge for fast changes anywhere. Brush holder screw Brushes Extra brushes Brush holder Replacement screw Fig. 15 Fig. 16 To reduce the chance of bit binding: • Use sharp bits. Sharp bits are less likely to bind when drilling. • Use the proper bit for the job. There are bits that are designed for specific purposes. • Use caution when drilling pitchy, knotty, wet or warped material or when drilling in material that may contain nails. Fig. 12 Forward rotation Reaction Bracing against the floor Forward rotation Bracing against your leg Reaction Bracing against a stud Fig. 14 Reverse rotation Reaction Forward rotation 2. Remove worn brushes. If the brushes should fall into the tool, be sure to shake them out before reinserting the cartridge. Discard BOTH brushes. Brushes should always be replaced in sets. 3. A set of spare brushes is provided in the cartridge. Remove the brushes from storage compartment. 4. Position new brushes with the flat silver end facing into the brush holder. Push cartridge into the tool and press evenly on top and bottom of the cartridge to align terminals for proper connection. 5. Tighten the brush holder screw gently. If the head of Screw is damaged, use the replacement screw provided in the cartridge. Never use a metal screw as a brush holder screw. WARNING! WARNING! To reduce the risk of injury, always unplug your tool before performing any maintenance. Never disassemble the tool or try to do any rewiring on the tool's electrical system. Contact a MILWAUKEE service facility forALL repairs. MAINTENANCE Maintaining Tools Keep your tool in good repair by adopting a regular maintenance program. Before use, examine the general condition of your tool. Inspect guards, switches, tool cord set and extension cord for damage. Check for loose screws, misalignment, binding of moving parts, improper mounting, broken parts and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, turn the tool off immediately and have the problem corrected (See Fig. 12 - 14). Bits may misaligned or when they are through a hole. Wood boring bits bind if they run into nails or knots. for bit binding situations. Typical Bracing Methods before further tool. Tag damaged tools USE” until repaired (see “Repairs”). Under normal conditions, not necessary until the motor need to be replaced. After six months to one year, depending on use, return your tool to the nearest MILWAUKEE service facility for the following: • Lubrication • Brush inspection and replacement • Mechanical inspection and cleaning (gears, spindles, bearings, housing, etc.) • Electrical inspection (switch, cord, armature, etc.) • Testing to assure proper mechanical and electrical operation WARNING! To reduce the risk of injury, electric shock and damage to the tool, never immerse your tool in liquid or allow a liquid to flow inside the tool. Cleaning Clean dust and debris from vents. Keep the tool handles clean, dry and free of oil or grease. Use only mild soap and a damp cloth to clean your tool since certain cleaning agents and solvents are harmful to plastics and other insulated parts. Some of these include: gasoline, turpentine, lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia and household detergents containing ammonia. Never use flammable or combustible solvents around tools. Repairs If your tool is damaged, return the entire tool to the nearest service c...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :