Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
To activate trigger lock move lever to the center off position. !CAUTION Do not change direction of rotation until the tool comes to a complete stop. Shifting during rotation of the chuck can cause damage to the tool. BELT CLIP (Optional Accessory) !WARNING When the tool is attached to the belt, position yourself to avoid entanglement with surrounding objects. Unexpected entanglement could cause the tool to fall resulting in injury to the operator or bystanders. -10 BM 2609140358 12-05 12/6/05 3:28 PM Page 11 The optional belt clip accessory will allow you to conveniently attach your tool to your belt. This feature will allow you to have both hands free when climbing a ladder or moving to another work area. The belt clip can be attached to either side of the tool by securing it with a mounting screw. Always make sure you securely tighten the mounting screw before use. To open clip, squeeze both release buttons and the clip will spring up automatically (Fig. 4). To use clip, turn tool upside down and attach to your belt. SWIVEL LIGHTING SYSTEM Your tool is equipped with integrated light source in the knurled thumbwheel. The light will go ON as soon as you squeeze trigger switch, unless the thumbwheel is in the 0 position (Fig. 5). The light beam can be adjusted to 3 positions in front of the chuck for the desired bit being used. Position 1: The focus of the beam is approximately 20 mm. Position 2: The focus of the beam is approximately 150 mm. Position 3: The focus of the beam is approximately 500 mm. Position 0: The beam is shut off permanently. To retract clip when not in use, push down on clip until it locks in the closed position. CLIP RELEASE BUTTONS FIG. 4 FIG. 5 ATTACHING GEAR BOX COVER 2. Slide gear box cover into place (Fig. 7). (Models 22618 & 23618 only) 3. Replace rubber guard to secure gear box 1. Remove rubber guard by pulling forward cover (Fig. 8). (Fig. 6). RUBBER GUARD FIG. 6 GEAR BOX COVER FIG. 7 RUBBER GUARD FIG. 8 FIG. 9 -11 BM 2609140358 12-05 12/6/05 3:28 PM Page 12 INSERTING AND RELEASING remove protective cap from battery pack. To BATTERY PACK insert battery, align battery and slide battery Release battery pack from tool by pressing pack into tool until it locks into position. Do on both sides of the battery release tabs and not force (Fig. 1). pull downward. Before inserting battery pack, IMPORTANT CHARGING NOTES 1. The battery pack accepts only about 80% of its maximum capacity with its first few charge cycles. However, after the first few charge cycles, the battery will charge to full capacity. 2. The charger was designed to fast charge the battery only when the battery temperature is between 40°F (4°C) and 105°F (41°C). 3. A substantial drop in operating time per charge may mean that the battery pack is nearing the end of its life and should be replaced. 4. If you anticipate long periods (i.e. a month or more) of non-use of your tool, it is best to run your tool down until it is fully discharged before storing your battery pack. After a long period of storage, the capacity at first recharge will be lower. Normal capacity will be restored in two or three charge/discharge cycles. Remember to unplug charger during storage period. 5. If battery does not charge properly: a. Check for voltage at outlet by plugging in some other electrical device. b. Check to see if outlet is connected to a light switch which turns power “off” when lights are turned off. c. Check battery pack terminals for dirt. Clean with cotton swab and alcohol if necessary. d. If you still do not get proper charging, take or send tool, battery pack and charger to your local Bosch Service Center. See “Tools, Electric” in the Yellow Pages for names and addresses. Note: Use of chargers or battery packs not sold by Bosch will void the warranty. -12 BM 2609140358 12-05 12/6/05 3:28 PM Page 13 CHARGING BATTERY PACK (30 MINUTE SINGLE BAY-BC130) CHARGER INDICATORS, SYMBOLS AND MEANING If the indicator lights are “OFF”, the charger is not receiving power from power supply outlet. If the green indicator light is “ON”, the charger is plugged in but the battery pack is not inserted, or the battery pack is fully charged and is being trickle charged. If the green indicator light is “BLINKING”, the battery pack is being fast-charged. Fast- charging will automatically stop when the battery pack is fully charged. If the red indicator light is “ON”, the battery pack is too hot or cold for fast-charging. The charger will switch to trickle charge, until a suitable temperature is reached, at which time the charger will switch automatically to fast-charging. If the red indicator light is “BLINKING”, the battery pack cannot accept a charge or the contacts of the charger or battery pack are contaminated. Clean the contacts of the charger or battery pack only as directed in these operating instructions or those supplied with your tool or battery pack. Plug charger cord into your standard power outlet. Before inserting battery pack, remove pr...
Ce manuel est également adapté pour les modèles :Perceuses et shuropopverty - 22614 (2.4 mb)
Perceuses et shuropopverty - 22612 (2.4 mb)
Perceuses et shuropopverty - 22618 (2.4 mb)
Perceuses et shuropopverty - 23609 (2.4 mb)