Évaluations - 5, GPA: 3.8
(
)
)
|
Par ce dispositif a également d'autres instructions :
Perceuses et shuropopverty - DV 18DL (475.33 kb)
Facilité d'utilisation
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from intended could result in a hazardous situation. 5) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. PRECAUTION Keep children and infirm persons away. When not in use, tools should be stored out of reach of children and infirm persons. English PRECAUTIONS FOR CORDLESS IMPACT DRIVER CAUTION ON LITHIUM-ION BATTERY DRILL 1. Always charge the battery at a temperature of 0 – 50°C. A temperature of less than 0°C will result in over charging which is dangerous. The battery cannot be charged at a temperature higher than 50°C. The most suitable temperature for charging is that of 20 – 25°C. 2. When one charging is completed, leave the charger for about 15 minutes before the next charging of battery. Do not charge more than two batteries consecutively. 3. Do not allow foreign matter to enter the hole for connecting the rechargeable battery. 4. Never disassemble the rechargeable battery and charger. 5. Never short-circuit the rechargeable battery. Shortcircuiting the battery will cause a great electric current and overheat. It results in burn or damage to the battery. 6. Do not dispose of the battery in fire. If the battery is burnt, it may explode. 7. When drilling in wall, floor or ceiling, check for buried electric power cord, etc. 8. Bring the battery to the shop from which it was purchased as soon as the post-charging battery life becomes too short for practical use. Do not dispose of the exhausted battery. 9. Using an exhausted battery will damage the charger. 10. Do not insert object into the air ventilation slots of the charger. Inserting metal objects or inflammables into the charger air ventilation slots will result in electrical shock hazard or damaged charger. 11. When mounting a bit into the keyless chuck, tighten the sleeve adequately. If the sleeve is not tight, the bit may slip or fall out, causing injury. To extend the lifetime, the lithium-ion battery equips with the protection function to stop the output. In the cases of 1 and 2 described below, when using this product, even if you are pulling the switch, the motor may stop. This is not the trouble but the result of protection function. 1. When the battery power remaining runs out (The battery voltage drops to about 12V (DV18DL) / about 8V (DV14DL)), the motor stops. In such case, charge it up immediately. 2. If the tool is overloaded, the motor may stop. In this case, release the switch of tool and eliminate causes of overloading. After that, you can use it again. English SPECIFICATIONS POWER TOOL Model DV14DL DV18DL No-load speed Low (Save MODE) 0-200 min–1 0-200 min–1 Low (Power MODE) 0-400 min–1 0-400 min–1 High (Save MODE) 0-850 min–1 0-900 min–1 High (Power MODE) 0-1750 min–1 0-1800 min–1 No-load impact rate (Low/High) 0 – 4800 / 0 – 21000 min–1 0– 4800 / 0 – 21600 min–1 Capacity Drilling Brick (Depth 30 mm) 14 mm 16 mm Wood (Thickness 18 mm) 45 mm 50 mm Metal(Thickness 1.6 mm) Steel: 13 mm, Aluminum: 13 mm Driving Machine screw 6 mm Wood screw 8 mm (diameter) . 75 mm (length) (Requires a pilot hole) 8 mm (diameter) . 100 mm (length) (Requires a pilot hole) Rechargeable battery BCL1430: Li-ion 14.4 V (3.0 Ah 4 or 8 cells) EBL1430: Li-ion 14.4 V (3.0 Ah 4 cells) EBM1430: Li-ion 14.4 V (3.0 Ah 8 cells) EBM1830: Li-ion 18 V (3.0 Ah 10 cells) Weight 2.1 kg 2.2 kg CHARGER Model UC18YRL Charging voltage 7.2 – 18 V Weight 0.6 kg STANDARD ACCESSORIES DV14DL (2LRK) 1Plus driver bit (No. 2 . 65L) ...... 1 2Charger (UC18YRL) .............................. 1 3Battery (BCL1430 or EBL1430 or EBM1430) .......................................... 2 4Side handle ...................................... 1 5Plastic case ....................................... 1 1Plus driver bit (No. 2 . 65L) ...... 1 2Charger (UC18YRL) .............................. 1 DV18DL 3Battery (EBM1830) ........................... 2 (2MRK) 4Side handle ...................................... 1 5Plastic case ....................................... 1 DV14DL (NN) D...