Évaluations - 4, GPA: 3.3
(
)
)
|
Facilité d'utilisation
Insert the bit or other accessory fully into the chuck, and tighten securely by holding the rear half of the chuck and rotating the front portion in the clockwise direction as viewed from the chuck end. DR220 -Single Sleeve Chuck with Automatic Spindle Lock -This tool is equipped with a feature that automatically locks the spindle when the tool is not running. This feature is a normal condition which allows for tightening or loosening of the chuck with one hand while holding the drill with the other. Loosen the chuck by rotating the sleeve counterclockwise (Fig. 3). Insert the bit or other accessory fully into the chuck, and tighten securely by rotating the sleeve in the clockwise direction as viewed from the chuck end. QUICK CHANGE ACCESSORY DR220 Only -A quick change accessory is included with the DR220 which allows for easy changing of hex shank accessories without loosening or tightening the chuck jaws. To use the quick change accessory, insert the shaft into the DR220 chuck and tighten securely. Insert a hex shank accessory by pulling back on the collar as shown in Figure 4. Release the collar and the bit is held firmly. To release the bit simpy pull back on the collar and pull the bit out. HAMMER ACTION (DR400, DR402, DR600) Your drill has hammer action which is engaged by sliding the hammer/drill selector lever. To select hammering, turn off the drill and rotate the lever shown in Figure 5 so that the arrow on the lever points to to the hammer symbol on the drill housing. To select drilling, turn off the drill and rotate the lever so that the arrow on the lever points to the drill symbol. WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur when changing accessories. DRILLING • Always unplug the drill when attaching or removing accessories. When attaching accessories in the drill chuck, it is important to securely tighten the chuck using all three holes to prevent slippage. When using a keyless chuck, hand tighten firmly. • Use sharp drill bits only. • Support and secure work properly, as instructed in the Safety Instructions. • Use appropriate and required safety equipment, as instructed in the safety instructions. • Secure and maintain work area, as instructed in the safety instructions. • Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it. • Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit. • Hold the drill firmly to control its twisting action.. • DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN RESULT. • Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last part of the hole. • Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming. • Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The lubricants that work best are sulphurized cutting oil or lard oil. Bacon grease will also serve. • When using twist drill bits to drill holes in wood, it will be necessary to pull the bits out frequently to clear chips from the flutes. • Plug in drill. Make sure switch turns drill on and off. KEYLESS CHUCK REMOVAL (DR200, DR210, DR220, DR402) UNPLUG DRILL. Tighten the chuck around the shorter end of a hex key (not supplied) of 1/4" (6.4mm) or greater size. Using a soft hammer, strike key sharply in a counterclockwise direction (when viewed from the front of the tool). This will loosen the chuck so that it can be unscrewed by hand. KEYED CHUCK REMOVAL (DR400) UNPLUG DRILL. NOTE: Before attempting to remove chuck, shift the drill into the drilling mode (not hammer, if so equipped ). Place chuck key in any one of the three holes in the chuck. Strike the key sharply in a counterclockwise direction (when viewed from the front of the tool). This will loosen the chuck so that it can be removed by hand. KEYED CHUCK REMOVAL (DR500, DR600) UNPLUG DRILL. NOTE: Before attempting to remove chuck, shift the drill into the drilling mode (not hammer, if so equipped). Place chuck key in any one of the three holes in the chuck. Using a soft hammer, strike the key in a clockwise direction. This will loosen the torx screw inside the chuck. Open chuck jaws fully, insert a torx screwdriver into front of chuck between jaws to engage screw head. Remove screw by turning clockwise (left-hand-thread). Place key in chuck. Using a soft hammer, strike key sharply in a counterclockwise direction. This will loosen the chuck so that it can be unscrewed by hand. WARNING: It is important to support the work properly and to hold the drill firmly to prevent loss of control which could cause personal injury If you have any questions on how to proper...