Log:
Évaluations - 3, GPA: 4.3 ( )

Instructions Porter-Cable, Modèle 90550107

Fabricant : Porter-Cable
Taille : 766.13 kb
Nom Fichier : a98193da-fa1e-46da-8b8e-38f11f2dc1af.pdf
Langue d'enseignement: enesfr
Aller à la télécharger



Facilité d'utilisation


So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit. NOTE: LI-ION batteries should not be put in checked baggage. STORAGE RECOMMENDATIONS 1. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold. 2. Long storage will not harm the battery pack or charger. Under proper conditions LI-ION batteries, can be stored for 5 years or more. 7 90550107 PC1800ID, PC1200ID 4/1/09 9:33 AM Page 8 CHARGING PROCEDURE PORTER-CABLE chargers are designed to charge PORTER-CABLE battery packs in 30-60 minutes depending on the pack being charged. 1. Plug the charger into an appropriate outlet before inserting the battery pack. 2. Insert the battery pack into the charger. (Fig. B) B 3. The LED will flash indicating that the battery is being charged. 4. The completion of charge is indicated by the LED remaining on continuously. The pack is fully charged and may be used at this time or left on the charger. CHARGER DIAGNOSTICS This charger is designed to detect certain problems that can arise with the battery packs or the power source. Problems are indicated by one LED flashing in different patterns. BAD BATTERY The charger can detect a weak or damaged battery. The LED flashes in the pattern indicated on the label. If you see this bad battery blink pattern, do not continue to charge the battery. Return it to a service center or a collection site for recycling. HOT/COLD PACK DELAY When the charger detects a battery that is excessively hot or excessively cold, it automatically starts a Hot/Cold Pack Delay, suspending charging until the battery has normalized. After this happens, the charger automatically switches to the Pack Charging mode. This feature ensures maximum battery life. The light flashes in the pattern indicated on the label. PROBLEM POWER LINE When the charger is used with some portable power sources such as generators or sources that convert DC to AC, the charger may temporarily suspend operation. The LED flashes in the pattern indicated on the label. This indicates that the power source is out of limits. LEAVING THE BATTERY IN THE CHARGER The charger and battery pack can be left connected with the LED glowing indefinitely. The charger will keep the battery pack fresh and fully charged. This charger features an automatic tune-up mode which equals or balances the individual cells in the battery pack to allow it to function at peak capacity. Battery packs should be tuned up weekly or whenever the battery no longer delivers the same amount of work. To use the automatic tune-up mode, place the battery pack in the charger and leave it for at least 8 hours. IMPORTANT CHARGING NOTES 1. Longest life and best performance can be obtained if the battery pack is charged when the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery pack in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage to the battery pack. 2. The charger and battery pack may become warm to touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed, or an uninsulated trailer. 8 90550107 PC1800ID, PC1200ID 4/1/09 9:33 AM Page 9 3. If the battery pack does not charge properly: a. Check current at receptacle by plugging in a lamp or other appliance b. Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. c. Move charger and battery pack to a location where the surrounding air temperature is approximately 65°F - 75°F (18°- 24°C). d. If charging problems persist, take the tool, battery pack and charger to your local service center. 4. The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the charging procedure. You may also charge a partially used pack whenever you desire with no adverse affect on the battery pack. 5. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean. 6. Do not freeze or immerse charger in water or any other liquid. : Shock hazard. Do not allow any liquid to get inside charger.Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, return to a service center for recycling. INSTALLING AND REMOVING THE BATTERY PACK FROM THE TOOL : Make certain the lock-off button is engaged to prevent switch actuation before removing or installing battery...

Ce manuel est également adapté pour les modèles :
Perceuses et shuropopverty - PC1800ID (766.13 kb)
Perceuses et shuropopverty - PC1200ID (766.13 kb)
Perceuses et shuropopverty - PCL180ID (766.13 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories