Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. 11. Avoid accidental starting. Ensure the switch is in the off- position before plugging in. Carrying tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. 12. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a
Fig. 4 Socket screw Ammeter gauge Meter box Socket screw and washer Cradle 6. Attach meter box to opposite side (see "Mounting the Meter Box"). For Cat. Nos. 4115 & 4120 only (Fig. 4). 1. Loosen the cradle lock. 2. Raise the cradle to the maximum height. 3. Lift the cradle an additional 1/2" by hand. 4. Tighten the cradle lock. 5. Loosen the socket head screw and remove the meter box. 6. Remove the meter box stud from the cradle. 7. Remove the screw and washer from the end of the pinion shaft. 8
1. Enlevez le joint caoutchoute de la base 2. Mettez le chassis au niveau avec les quatre (4) boulons de nivellement. 3. Selon les instructions du fabricant, installez une cheville d’ancrage a expansion dans la surface. Alignez la fente de la base du chassis Dymorig sur la cheville d’ancrage, puis inserez une tige ou un boulon filete au travers de la base dans l’embout filete de la cheville d’ancrage. Serrez fermement le boulon ou l’ecrou et la rondelle dans la cheville d’ancrage, selon le cas.
Always position the GFCI as close as possible to the power source. page 5 TOOL ASSEMBLY WARNING! To reduce the risk of injury, always unplug tool before attaching or removing accessories or making adjustments. Use only specifically recommended accessories. Others may be hazardous. Assembling Dymorigs & Vac-U-Rig® Stands For Cat. No. 4125 & 4130 only (Fig. 1). Fig. 1 Handle spoke Cradle assembly Column Base Leveling screws (4) Column bolts Socket set screws (2) Hex bolt 1. Set the base on the gro
3. Level the rig with the four (4) leveling screws using the bubble level (4125 & 4130 only) as a guide. When the rig is level, tighten the four (4) nuts (4125 & 4130 only) on the leveling screws. 4. Connect one end of the supplied vacuum hose to the vacuum line coupler on the vacuum pad. To do this, pull back the collar on the hose and push the end of the hose onto the coupler until in snaps into place. Then, connect the other end of the vacuum hose to the coupler on the vacuum pump following t
Le montant, le chassis, le moteur et la base devraient etre fermement fixes pour eviter toute vibration durant le carottage. • Assurez-vous que le moteur soit du calibre (intensite de courant et rotation) compatible avec le diametre du carottier utilise (consulter le guide du moteur dans le catalogue). • Assurez-vous toujours que l’outillage de carottage soit monte rigidement avec une cheville d’ancrage ou un coussin a vide, car tout mouvement ou toute vibration pourraient endommager le carottie
6845 -Adjustable Stopper Base with 7 settings for different screw lengths Sturdy aluminum casing Stopper base with anti-tilt device for preventing screws from swaying Rubber cap securely adhered to stopper base Dust-proof construction for smooth sliding action A Anti-tilt device for sure positioning and preventing swaying Lightweight 1.9kg (4.2lbs)
6845 -Adjustable Stopper Base with 7 settings for different screw lengths Sturdy aluminum casing Stopper base with anti-tilt device for preventing screws from swaying Rubber cap securely adhered to stopper base Dust-proof construction for smooth sliding action A Anti-tilt device for sure positioning and preventing swaying Lightweight 1.9kg (4.2lbs)
6845 -Adjustable Stopper Base with 7 settings for different screw lengths Sturdy aluminum casing Stopper base with anti-tilt device for preventing screws from swaying Rubber cap securely adhered to stopper base Dust-proof construction for smooth sliding action A Anti-tilt device for sure positioning and preventing swaying Lightweight 1.9kg (4.2lbs)
194500-1 For Model Size Length (mm) Part No. 6842, 6843 No.2 162 B-10481 6844 No.2 182 B-10475 6845 No.2 122 A-45858 Comparison of Efficiency Note: 1. It may differ under some conditions. 2. Numbers in the charts below are relative values when the capacities of Makita Model 6834 are indexed at 100. Test conditions: Test conditions: Drove 35mm drywall screws through a plasterboard into Douglas-fir timber. Drove 55mm drywall screws through three plasterboard into Douglas-fir timber.