Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
The baking grill may remain in the oven. 2. Pour approx. 400 ml of water mixed with a little dishwashing detergent into the floor pan of the oven cavity. In the case of heavy soil build-up, you may wish to allow the cleaning solution to soak in for a while before you activate the cleaning function. 3. Close the oven door. CAUTION: . The oven cleaning function can only be switched ON when the oven has cooled down completely. 4. Turn the function selector to position x. . The x indicator light and the C indicator light for oven temperature illuminate. * is displayed. If * flashes, the oven has not cooled down completely. . After the initial heating time (approx. 4 minutes) the oven temperature control lamp extinguishes. After a further 17 minutes the program cycle is completed. A buzzer sounds. Switching OFF: Turn the function selector to the { position. The oven cleaning control lamp extinguishes. Function selector Cleaning and Care After deactivating the oven cleaning function: Cleaning tips: . Never leave the residual water in the oven for any length of time, e.g. overnight. 1. Open the oven door and pick up the remaining water with a large absorbent sponge cloth. 2. Using the detergent-soaked sponge cloth, a soft brush or a plastic pot scrubber, wipe of the oven interior. Stubborn soil remnants can be removed with a cleaning scraper for glass- ceramic. Caution: Use the scraper carefully, and do not apply the tool at too flat an angle, because the enamel could be scratched! 3. Calciferous deposits may be removed with a cloth soaked in vinegar. 4. Wipe clean with clear water and dry with a soft cloth (do not forget to wipe under the oven door seal). Cleaning tips: . If the oven is heavily soiled, the procedure may be repeated after the oven has cooled. . If the oven is heavily soiled with grease, e.g. after roasting or grilling, we would recommend rubbing any stubborn dirt with detergent before activating the oven cleaning function. . After cleaning, leave the oven door in its slanted detent position, i.e., at a 30-degree angle, to allow the interior enamel surfaces to dry thoroughly. Rapid drying: 1. Place the oven door into the slanted detent position, at an angle of approximately 30 degrees. 2. Turn the function selector to position v. 3. Reduce the oven temperature with the temperature selector until 50° C is displayed. 4. Duration: approximately 5 minutes. 5. Then switch the oven off. Cleaning and Care Manual cleaning steps: Note: To make the manual cleaning steps following the automatic oven cleaning function more convenient, the appliance features the following options: Removing the oven door: 1. Fully open the oven door. 2. Move the catch levers on the right and left-hand sides to the fully open position. 3. Placing the door at an upward angle toward you, grasp the door with both hands and lift it out of the hinges toward you. Hanging the oven door: 1. Set both hinges into their respective receptacles on the left and right, and swing the oven door downward. 2. Close the catch levers on the left and right. 3. Close the oven door. Switching on the oven light: . Turn the function selector one setting to the left. The m symbol illuminates. Removing the suspend grids: 1. On both left and right sides, remove two milled screws each. 2. Carefully remove the suspended grids. Lowering the heating element: Caution: The heating element must have been allowed to cool. 1. Unlock the heating element by turning the ratchet at the ceiling of the oven cavity. Caution: in the lowered position, never switch on the heating element or place any weight on it. 2. After cleaning, swing the heating element again upward, and latch it into place. 1. 2. Service and Repair Information In the event of problems or repairs that you cannot solve or perform yourself, our customer service will be happy to help. Check the customer service directory for a customer service facility in your area. Caution: Calling the customer service because of an operator error can be very costly! In the event of a customer service request, please have the following information handy: E-Number FD You can find this information on the appliance‘s nameplate. The nameplate is located on the appliance, behind the oven door, on the left bottom edge of the oven. Replacing the oven light: Caution: Unplug the appliance or remove the fuse! 1. To prevent damage, place a dish towel into the cold oven. 2. Remove the glass cover by inserting a knife or similar object between the glass and the frame. 3. Replacing the lamp: –Type: Incandescent bulb E 14, 230 - 240 V, 25 W, heat resistant to 300° C. –You can obtain this lamp from customer service. Replacing the oven door seal: 1. Remove the defective oven door seal by simply unhooking it. You may obtain the new oven door seal from your customer service. Trouble-shooting Guide Calling the customer service is not always really necessary. In some cases, you can remedy the situation yourself. The following table may contain ...
Ce manuel est également adapté pour les modèles :Fours - B1641N2/01 (1.08 mb)
Fours - B1641N2/05 (1.08 mb)
Fours - B1641S2/01 (1.08 mb)
Fours - B1641W2/01 (1.08 mb)