Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
3. Lift the door panel slightly and remove it in the direction of the hinges. Removing the intermediate panel Before removing, make a note of the position in which the intermediate panel is fitted, so that you do not refit it the wrong way round later. 1. Press the left and right-hand holders outwards. The intermediate panel disengages upwards. 2. Lift the intermediate panel slightly and take it out. Cleaning Clean the door panels with glass cleaner and a soft cloth. Caution! Do not use any sharp or abrasive medium or a glass scraper. The glass could be damaged. Fitting the intermediate panel 1. Insert the intermediate panel on the left and right into the supports. 2.Push the intermediate panel downwards in the retainers. Fitting the door panel 1. Insert the door panel on the left and right into the supports. 2. Press the door panel downwards into the plug-in holders. 3.Refit the appliance door. Cleaning the hook-in racks You can remove the hook-in racks for easier cleaning. a=Risk of burning due to hot components in the cooking compartment! Wait until the cooking compartment has cooled down. 1.Push the hook-in rack upwards at the front and unhook to the side. 2.Pull the hook-in rack forwards at the rear and unhook to the side. 3.Clean the hook-in racks with washing-up liquid and a sponge or brush. 4.Align the hook-in rack with the indentation (a) facing upwards, so that the shelf heights match. 5. Insert the hook-in rack at the rear until the limit stop. 6.Push the hook-in rack towards the rear. 7. Insert the hook-in rack at the front until the limit stop. 8.Push the hook-in rack downwards. F a ults a n d re pa irs It is not always necessary to call the after-sales service. Sometimes, you can find a remedy yourself. You will find some tips for troubleshooting in the following table. Problem Possible cause Remedial action Electrical operation is malfunctioning (e.g. Fuse defective Check fuses in the fuse box and replace if indicator lamps do not light up) necessary Liquid or thin dough runs to one side Appliance not installed level Check the appliance installation ( see the Installation instructions) ‹ : ‹‹ flashes in the clock display There was a power cut Reset the clock ( see section: Electronic clock) Electronically controlled functions are mal- Energy surges ( e.g. lightning strike) Reset the function concerned functioning Smoke is generated during roasting or grill- Fat is burning on the grill element Continue grilling or roasting until the fat on ing the grill element is burnt away Wire rack or universal pan inserted incor- Place the wire rack in the universal pan rectly and insert them together at a lower shelf height High levels of condensation are generated Normal occurrence (e.g. when baking with Open the appliance door briefly from time in the cooking compartment very moist toppings or roasting a large to time during operation joint) Enamelled accessories have light, matt Normal occurrence caused by dripping Not possible marks meat or fruit juices Door panels are misted up Normal occurrence caused by tempera- Heat the appliance up to 100 °C and then ture differences switch off again after 5 minutes Replacing the oven light bulb Replace faulty oven light bulbs. Spare bulbs can be obtained from the after-sales service or specialist retailers. Use the following oven lights for the top oven and the main oven: E14, 220 - 240 V, 25 W, heat- resistant to 300 ° C a= Risk of electric shock ! Disconnect the appliance from the power supply. Switch off the circuit breaker or remove the fuse from the household fuse box. 1. Place a tea towel in the cold cooking compartment to prevent damage. 2. Turn the glass cover anticlockwise and remove it. 3. Replace the oven light bulb with a bulb of the same type. 4. Screw on the glass cover again. 5. Remove the tea towel and switch on the circuit breaker. Note: Use rubber gloves if the glass cover cannot be unscrewed: Or order a special removal tool from the after- sales service: ¦ For the main oven: Order no. 613634 ¦ For the top oven: Order no. 621743 Changing the door seal If the door seal is defective, it must be replaced. Replacement seals for your appliance can be obtained from the after- sales service. The door seal is attached in four places ( figure A) . When replacing it, disconnect and attach the hooks at all four points (figure B) . Check again to ensure that the seal is seated correctly in the corners in particular. After- sales service Our after- sales service is there for you if your appliance needs to be repaired. We will always find the right solution in order to avoid unnecessary visits from a service technician. E number and FD number When calling us, please give the product number ( E no.) and the production number (FD no. ) so that we can provide you with the correct advice. The rating plate containing these numbers can be found on the right-hand side of the oven door. You can make a note of the numbers of your appliance and the telephone number...
Ce manuel est également adapté pour les modèles :Fours - U17M72N0GB/35 (541.03 kb)
Fours - U17M72S0GB/08 (541.03 kb)
Fours - U17M72S0GB/35 (541.03 kb)