Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
Set this to correspond with the type of connection used with your TV. S-Video+CVBS: S-Video or Composite Video P-Scan: Component Video (Progressive Scan) YUV: Component Video S-Video+CVBS HDMI Video Sets the HDMI video output mode. HDMI Video must be enabled for DVD upconversion. Auto Angle Mark Displays an on-screen prompt whenever an alternate angle becomes available for viewing (press ANGLE to view). On Page SETUP SETUP Item Description Default Setting Screen Saver The screensaver prevents burn-in damage to television displays. On Last Memory Set the Last Memory function on or off. On Speaker Settings Use the Navigation Keypad to highlight the desired speaker selection and press to confirm. Item Description Default Setting 3D/EQ Sets the audio equalizer option (Off, 3D, Rock, Classic, Jazz, Pop). Off Reverb Sets the audio reverb effects option (Normal, Living Room, Hall, Arena, Cave, Concert Hall, Bathroom, Church). Off Audio Settings Use the Navigation Keypad to highlight the desired audio selection and press to confirm. Item Description Default Setting Digital Output Sets the digital audio output signal type (PCM, RAW, OFF). For use with digital decoding receivers (see your receiver’s manual for more information). RAW Channel Output Sets the audio channel mix mode (LT/RT, Stereo). Stereo HDMI Audio Set the HDMI audio function on or off. Turn HDMI Audio off to use HDMI video with an alternate audio connection (e.g., Coaxial Digital Audio). On Parental Settings Use the Navigation Keypad to highlight the desired parental selection and press to confirm. Item Description Default Setting Password You must input the four-digit password to access the Parental settings. The initial password is 8888. Change Password Enter the old password, the new password, and then the new password again to verify and change the Parental Settings password. Restoring the player’s default settings will not reset the password. DO NOT FORGET THE PASSWORD; this password cannot be reset. Page Coby Electronics CorporationPage Coby Electronics Corporation SETUP SETUP Item Description Default Setting Rating Level Sets the maturity rating level of the player. The player will not play any discs rated higher than this setting. There are eight rating levels. Level 1 will restrict playback to discs suitable for people of all ages. Level 8 will allow playback of all discs, including those suitable for adults only. 8 Default Resets all options to their factory-default state. Page SPECIFICATIONS SPECIFICATIONS Display Type On-Screen Disc/Media Support DVD, DVD±R/RW, CD, CD-R/RW, JPEG Video Formats MPEG-1, MPEG-2, MPEG-4 Audio Formats MPEG 1 Layer 1 & Layer 2 Video Output HDMI (Upconversion) Component Video (Progressive Scan) S-Video Composite Video Audio Output Coaxial Digital Audio RCA 2-Channel Stereo Audio HDMI Output Modes 720x480p, 720x576p, 1280x720p, 1920x1080i Digital Audio Decoders Dolby Digital Video System NTSC/PAL Power AC 100-240V ~50/60Hz 20W (max) Unit Dimensions 11.80” x 1.55” x 8.65” (WHD) Design, specifications and manual are subject to change without notice. 283SS Page 0Coby Electronics CorporationPage 0 Coby Electronics Corporation TROUBLESHOOTING TROUBLESHOOTING If you have a problem with this player, please read the troubleshooting guide below and check our website at for Frequently Asked Questions (FAQs) and firmware updates. If these resources do not resolve the problem, please contact Technical Support. COBY Electronics Technical Support 56-65 Rust Street Maspeth, NY 11378 Hours: 8:00 AM–11:00 PM EST, seven days a week. Email: techsupport@cobyusa.com Phone: 718-416-3197, 800-681-2629, or 800-727-3592 Web: There is no power to the device. • Ensure that the Power Switch on the main unit is physically set to the ON position. • Ensure that the AC adapter cord is securely connected to the player and the proper wall outlet. The device will not play the disc. • Ensure that a supported disc is loaded in the player label-side up. • Ensure that the disc’s rating level does not exceed the player’s parental rating level. • Ensure that the disc is not damaged or too dirty. Clean the disc or try another disc. • Moisture may have condensed inside the player. Remove the disc and leave the player on for 1-2 hours and then try again. There is no picture. • Ensure that the TV set has been powered on and is set to the correct AV mode. • Ensure that the connections between the player and the TV are secure and correct. • Check if the connection cables are damaged. • Restore the player to it’s factory-default settings: open the disc tray, and then press the PRG and ZOOM together on the remote control. The picture is noisy or distorted. • The disc may be damaged or dirty. Clean the disc or try another one. • Reset your TV’s color system. • Ensure that the player is connected directly to the TV (and not through a VCR, cable box, satellite rec...