Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
3. Press the PLAY button to resume normal playback. Still Picture and Frame Advance 1. Press the PAUSE II button during playback. This will freeze the picture on your TV. 2. If the picture vibrates vertically during still mode, use the CH +/-buttons to adjust for minimum distortion. If noise bars appear on the screen during still mode, set your VCR to the slow mode and press the CH +/-buttons to make the noise disappear. Then press the PAUSE II button again. 3. Press the PAUSE II button during still mode for frame advance. 4. Press the PLAY button again to resume normal playback. Note: • Sound is muted during still picture, video search, frame advance and variable slow motion. Automatic Tracking Control System This function automatically adjusts the tracking to match the recorded tape. Auto tracking engages in the following cases: • When you insert the cassette and begin playback. • When you press the CH +/-buttons at the same time. • When the VCR has been playing back an unrecorded section of tape, and then reaches a recorded tape segment. When auto tracking engages, “PLAY” on the TV screen flashes for a few seconds. Poor Tracking Normal Picture Manual Tracking Control When a poorly recorded tape is playback or the VCR is near an electrical or magnetic field, auto tracking may not operate normally. In this event, manually adjust the tracking with the CH +/-buttons to make any noise disappear. Blue Screen Noise Elimination Set the BLUE SCREEN mode to ON on the SETUP button selection screen. (See Mode Selection .) This function eliminates monitor noise and mutes sound during playback of unrecorded portions of a tape and when receiving a non-broadcasting channel. Blue Screen will also appear if the VCR is set to the Auxiliary mode but no video signal is fed to the VCR. (The BLUE SCREEN mode is set to ON at the factory.) Notes: • Blue Screen does not function during still picture, variable slow motion and video search. • Blue Screen may not function properly if the broadcast signal is too strong or too weak. • Blue Screen does not function during playback of a tape with noise recorded. • If the antenna signal is weak while recording a TV programme or if the input signal is weak while tape dubbing, the monitor screen may turn blue since the unit may not recognize whether or not a proper signal is being received. In this event, set the BLUE SCREEN mode to OFF. - 49 - (continued on next page) (continued on next page)(continued on next page)(continued on next page)(continued on next page)(continued on next page) VCR Playback Quick Start with Full Loading Mechanism Your VCR has a standby function (Full Loading Mechanism) to allow immediate recording and playback. After pressing the REC or PLAY button, it takes about 2 seconds until recording or playback is engaged when in the standby mode. Full Automatic Playback The Full Automatic Playback lets you enjoy playback with ease.When you insert a cassette with the erasure protection tab removed, your VCR automatically turns on the power and playback the tape. When the tape reaches its end, the VCR automatically rewinds the tape, turns its power off and ejects the tape. Note: • If the erasure protection hole is covered, press the PLAY button after the power turns on automatically. Audio Output Mode Your VCR has 3 channels for audio recording (2 on the Hi-Fi track and 1 on the linear track).You can select the audio output channels in playback mode on the SET UP selection screen. The following shows which audio channels will be heard when a stereo Hi-Fi video cassette is playback while a stereo system is properly connected to the VCR. (See Mode Selection .) Hi-Fi L + R mode: LR Normally, select Hi-Fi L + R mode on the SET UP selection screen: both the left (L) and right ( R) audio channels will be taken from the Hi-Fi audio track. Normally you will not have to change to another mode. (See Recording MTS (Multi-channel TV Sound) Broadcasts.) Hi-Fi L mode: L The left channel of the Hi-Fi audio track will be playback through both speakers. Hi-Fi R mode: R The right channel of the Hi-Fi audio track will be playback through both speakers. Linear mode: MONO The audio signal recorded on the linear audio track will be playback through both speakers. Note: • When video cassettes recorded on a non-Hi-Fi VCR are playback or the Hi-Fi audio output level is poor, the audio signal recorded on the linear audio track will automatically be playback regardless of the audio output mode. - 50 VCR Recording IMPORTANT This Unit does NOT allow copying from DVD to VCR tape Recording aTV Programme Preparation • Turn on the TV and select the video channel. (See Setting the 3 - 4 Output Channel.) • Press the VCR ON/OFF button (VCR ON indicator will light up) and then TV/VCR to select “VCR” (TAPE IN indicator will light up). • If necessary, set “SAP” on the SETUP selection screen. (See Mode Selection.) Without a Cable Box or Digital Satellite Receiver 1. Insert the cassette, with the erasure protectio...