(Refer to page 12.) 2 Eject (0) button This button is used to eject the disc. 3 BUSY indicator Flashes during data access. 4 DVD indicator Lights when a DVD is loaded. 5 Volume Control (headphone level) This is used to adjust the volume level of the headphone jack. 6 Headphone jack (PHONES) This is a stereo minijack for headphones. 7 Hole for forced ejection When the eject button has lost its function, insert an accessory pin for emergency ejection into this hole and push to eject the disc. (Refer to page 13.) WARNING: OBefore executing this operation, be sure to switch off the power supply of the computer and confirm that the disc loading is stopped. It takes approx. 30 seconds to stop loading a disc after switching off the power supply. OAlways use the pin provided (Do not use other objects). En A HARDWARE TOUR REAR VIEW - 8 Audio output Fig. 2089 4 1 8 501 49 1 2 +5 G G +12 DC INPUT This is a connector for output of analog audio. As a Molex 70553 type connecter is used, select a matching connection cable. 9 Function switch Use the accessory short-circuit sockets to set the SCSI ID number and the drive function. OON : short circuited OOFF : open #1 ~ 3 : SCSI ID * The factory setting is for ID No. 2. Setting switch SCSI-ID 0 1 2* 3 4 5 6 7 0 (LSB) (#1) OFF ON OFF ON OFF ON OFF ON 1 (#2) OFF OFF ON ON OFF OFF ON ON 2 (MSB) (#3) OFF OFF OFF OFF ON ON ON ON #4 : Reserved #5*1 : SCSI Terminator ON = SCSI termination disable OFF = SCSI termination enable #6 : Default sector size ON = 512 byte OFF = 2048 byte #7 : Disable the eject switch ON = Disables the eject switch OFF = Enables the eject switch 8 7 6 5 4 3 2 1 DISABLE EJECT 2048/512 TERMINATION (SHORT – OFF) RESERVED SCSI ID 2 1 0 Switch # RPC SET #8*1*2 : RPC (Region Play Control) Set ON = Stay in RPC Phase I mode OFF = Start RPC Phase II mode (Never return to Phase I mode after Phase II mode is used) *1 Pin 5 (TERMINATION) and Pin 8 (RPC SET) are ON at the time of shipping from the plant. *2 For a DVD Video playback system (computer) for Phase I, please use with Phase I. When the DVD Video playback system (computer) and the drive have different region codes, DVD Video playback is not possible. Set the jumper switch to OFF only when use of a drive corresponding to Phase II has been specified clearly for the DVD Video playback system (computer). The drive will be initialized automatically and will operate in Phase II mode. 0 SCSI interface This is a 50-pin I/O connector according to the SCSI-2 specifications. Use a flat ribbon SCSI connector to connect to the SCSI host adapter. -DC Input This is the power supply input for DC +5 V and +12 V. En TO INSTALL THE DRIVE Fig. 3 BUSYDVD PHONES DVD-ROM DRIVE OSwitch off the power of the personal computer and remove the cover or the front panel. ORemove the blank panel installed at the front of the 5.25 inch slot. Installation is not possible when there is no empty slot. OInstall the fixation slide rails on the drive. (If slide rails are required, contact the shop where you bought the computer or the computer manufacturer.) OInsert the drive into the slot. OIf fixing is required, fix the drive according to the instruction manual for the computer. Use mounting screws with a length of 5 mm (3/16 in.) or less. Use of long screws may damage the drive. Install the drive after the power supply of the personal computer has been switched off. When the mounting screws are loose etc., the vibrations from disc rotation can generate a ripping noise, so that the screws should be tightened securely. The drive installation method differs according to the computer type. For details, please refer to the manuals of your computer. En CONNECTING THE DRIVE IN THE MIDDLE OF A SCSI CHAIN Sound Board SCSI hard disk DVD-U02 Pin 1 Pin 1 SCSI Interface Cable Audio Cable To the power supply of the personal computer SCSI HOST Adapter Into an expansion slot of the personal computer Fig. 4 When a SCSI hard disk or other SCSI equipment also is installed in the computer, please connect according to the following method. ¦Switch off the power supply of the personal computer. ¦Set the SCSI ID number so that it is different from the ID numbers of all other SCSI units. ¦Set the termination OFF. ¦Connect the power supply cable from the personal computer. At the time of connection, pay attention to the cable polarity. Please use a power supply cable with two or more connectors in parallel. ¦Connect the SCSI interface cable. At this time, confirm that the pin 1 of the SCSI connector is connected correctly to pin 1 of the cable. Use a cable with two or more connectors in parallel. ¦When a sound board is used, connect the audio output with an audio cable to the sound board. WARNING The power supply of the personal computer always must be switched off before cables are connected. En CONNECTING THE DRIVE AS THE ONLY SCSI DEVICE Fig. 5 Pin 1 Power Cable SCSI Interface Cable Audio Cable SCSI HOST Adapter Sound Board To th...
