Évaluations - 0, GPA: 0
(
)
)
|
Photos et spécifications Sony DVP-S505D |
Facilité d'utilisation
Speaker Set Up To obtain the best possible surround sound, first specify the type of speakers you have connected and their distance from your listening position. Then use the test tone to adjust the speaker volumes to the same level. SET UP ENTER ?/>/.// Specifying the speaker type 1 Press SET UP and select “ 1”, then press ENTER. 2 Select the speaker you want to adjust in “SPEAKER SETUP” and press ENTER. 3 Select the appropriate symbol for the speaker, then press ENTER. pFront speaker, Center speaker, or Rear speaker Normally select this symbol. This is default setting. When the sound cracks or the effects of the surround is difficult to hear, select this symbol. This activates the Dolby Digital (AC-3) bass redirection circuitry and outputs the bass frequencies of the speaker from some other speakers . If you will not connect the speaker, select this symbol. You cannot select this symbol for the front speakers. p Sub woofer If you connect a sub woofer, select this symbol to output the LFE (low frequency effects) channel from the sub woofer. This is default setting. If you do not connect a sub woofer, select this symbol. This activates the Dolby Digital (AC-3) bass redirection circuitry and outputs the LFE signals from other speakers. Notes • The cut off frequency for the subwoofer is fixed at 100Hz. • Set the subwoofer‘s cut off frequency as high as possible. • Depending on the settings of other speakers, the subwoofer may output excessive sound. • The bass management options provided by the bass redirection circuitry in this player will optimize system setup based on total system configuration selected. In some instances, independent speaker selections might be changed to reflect the most optimum multi-channel sound experience. • If your speakers are too small to reproduce low bass frequencies, please set all speaker settings to “ (small)” and utilize a subwoofer for low frequency sound. Symbol 5. 1 OUTPUT SETUP 1 SPEAKER SETUP FRONT REAR ENTER QUIT SETUP SUBWOOFER DISTANCE FRONT 3. 0m CENTER CENTER REAR 3. 6m 3. 6m 1 2 1 2 Note When you select a symbol, the sound cuts off for a moment. 38EN Dolby Digital Surround Dolby Digital Surround Specifying the speaker distance 1 Press SET UP and select “ 1”, then press ENTER. 2 Select the speaker you want to adjust in “DISTANCE” and press ENTER. 3 Adjust the value using >/., then press ENTER. Note When you set the distance, the sound cuts off for a moment. You can vary the distance of each speaker as follows. Default adjustments are in the brackets. pFront speaker (3.6 m) • Front speaker distance can be set in 0.2 meter steps from 1 to 15 meters. • If both speakers are not placed an equal distance from your listening position, set the distance of the closest speaker. pCenter speaker (3.6 m) Center speaker distance can be set in 0.2 meter steps from a distance equal to the front speaker distance to a distance 1 meter closer to your listening position. Note Do not place the center speaker farther away from your listening position than the front speakers. pRear speaker (3.0 m) • Rear speaker distance can be set in 0.2 meter steps from a distance equal to the front speaker distance to a distance 5 meters closer to your listening position. • If both speakers are not placed an equal distance from your listening position, set the distance of the closest speaker. Note Do not place the rear speaker farther away from your listening position than the front speakers. Adjusting the speaker volume 1 While you stop playback, press SET UP and select “ 2”, then press ENTER. 2 Set “TEST TONE” to “ON.” You will hear the test tone from each speaker in sequence. 3 From your listening position, adjust the value of “BALANCE” and “LEVEL” using >/.and ENTER. During this adjustment, the test tone is emitted from both speakers simultaneously. 4 Set “TEST TONE” to “OFF” to turn off the test tone. 5. 1 OUTPUT SETUP 2 TEST TONE: FRONT ENTER QUIT SETUP REAR LEVEL CENTER BALANCE SUBWOOFER MODE: OFF OFF 0. 0dB REAR 0. 0dB 0. 0dB 0. 0dB 0. 0dB 1 2 1 2 Note While you are playing a disc, you cannot here the test tone. You can vary the balance and the level of each speaker as follows. Default adjustments are in the brackets. pFront speaker balance (0dB) Adjust the balance between the front left and right speakers (-8dB [L] ~+8dB [R], 0.5dB steps). pRear speaker balance (0dB) Adjust the balance between the rear left and right speakers (-8dB [L] ~+8dB [R], 0.5dB steps). pCenter speaker level (0dB) Adjust the level of the center speaker (-20dB ~+6dB, 0.5dB steps). pRear speaker level (0dB) Adjust the level of the rear speakers (-20dB ~+6dB, 0.5dB steps). pSub woofer level (0dB) Adjust the level of the sub woofer (-10dB ~+6dB, 0.5dB steps). The test tone does not be output from the subwoofer. To adjust the volume of all the speakers at one time Use the amplifier‘s volume control. To return to the default setting Select the sybol or the item, then press CLEAR. 39EN Dolby Digital Surround Dolby Digital Sur...