Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
E36 Already finalized video format disc • A program with the error number is grayed in the timer programming list. • Once the timer programming list with error line(s) is displayed, or after canceling and setting again the timer standby mode, the program line(s) with error will be cleared. *1 PCA is a disc's space reserved for recording test. Note • Press [TIMER PROG.] to check the timer recording in progress. When the timer recording is proceeding, that program will be highlighted in red. In this case, you cannot select any other program. To stop the timer recording in progress TIMER RECORDING Press [STOP C] to stop the disc recording or [ A EJECT / C STOP] to stop the cassette tape recording on the front panel of the unit. [STOP C] on the remote control is not effective. E9KGBUD_D-KVR20KU_EN.indd 40 2008/05/27 16:10:39 EN 41 MDanisacg ement Recording Playback Introduction Connections Basic Setup Editing Function Setup VCR Function Others TIMER RECORDING Hints for Timer Recording PROG. A PROG. B actual recording PROG. A PROG. B When the starting time is the same: A program set previously (PROG. A) has priority. The first 2 minutes (at the longest) will be cut off. PROG. A PROG. B actual PROG. A recording PROG. A PROG. C PROG. B PROG. C When the starting time and the ending time for each programs are different: A program that has earlier start time has priority. The first 2 minutes (at the longest) will be cut off. PROG. A PROG. B actual recording PROG.B PROG.A When the recording time is partially overlapped: PROG. A will start after PROG. B is complete to be recorded. The first 2 minutes (at the longest) will be cut off. PROG. A PROG. B actual recording PROG. B When the recording time is entirely overlapped: PROG.A will not be recorded. This unit records the programs according to priority if the timer programmings are overlapped. The timer programming set previously has priority. A timer recording of lower priority will be canceled or start from the middle. Check the overlapped timer programmings and change the priority if necessary. • If there is a power failure or this unit has been unplugged for more than 30 seconds, the clock setting and all timer programming will be lost. • If a disc is not inserted or if a inserted disc is not recordable (finalized DVD-RW/-R, finalized DVD+RW, a fully recorded disc, etc.), “DVD” on the front panel display flashes and timer recording cannot be performed. In some cases, will appear momentarily around the start point as the unit attempts to record. Please insert a recordable disc. • If a cassette tape with an erase-protection tab is not in the cassette compartment or there is no cassette tape in the cassette compartment, “VCR” on the front panel display flashes and timer recording cannot be performed. Please insert a recordable cassette tape. • If you press [TIMER SET] and turn on the unit while either DVD or VCR is in timer standby mode, disappears. In this case, you cannot change the mode between DVD and VCR. You cannot change any settings using [SETUP] or edit discs. • When all the timer recording is completed, flashes. To play back or eject the recorded disc, press [I/y ON/STANDBY] first, then select the recorded title and press [PLAY B], or [OPEN/CLOSE A] to remove the disc. • During timer recording or timer standby mode ( will appear), any operations on the unit will not be available. To make these operations available, press [C STOP] on the front panel to cancel the timer recording or [TIMER SET] to release timer standby mode ( will disappear). • To cancel the timer standby mode, press [TIMER SET]. • When the starting and the ending time are the same, “Exceeds 12 hours” appears and the program setting will not be accepted. • When the programmed starting and ending time are earlier than the current time, the setting will not be accepted. • If the starting time is earlier and the ending time is later than the current time, the recording will start right after [TIMER SET] is pressed. • The timer recording cannot be performed in DVD and VCR at the same time. If you set 2 programming with the same channel and time in both devices, the program with a lower program number will be recorded. The Priority of Overlapped Settings Note for DVD recording • When the recording time of 2 programs are overlapped, or the end time of a program and the start time of another program is the same, the first 2 minutes (at the longest) of the subsequent program will be cut off. • If the cut-off portion comes up to 3 minutes or more, this program will be displayed with errors number E40 in the timer programming list. PROG. A PROG. B actual recording The first 2 minutes (at the longest) will be cut off. PROG. A PROG. B When the end time of the programming currently being recorded and the start time of the subsequent program are same: The beginning of the PROG. B may be cut off. E9KGBUD_D-KVR20KU_EN.indd 41 2008/05/27 16:10:39 42 EN SATELLITE LINK You can set the unit to start recording when...
Ce manuel est également adapté pour les modèles :Lecteur DVD - D-VR600 (23.93 mb)