Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
(1 sec) BEEP ALL The beep is generated when any key is pressed. Using the EQ (Equalizer) Press EQ/XDSS repeatedly. The indicator lights up in the following order. Pop t Classic t Rock t Jazz t Vocal t Salsa t Samba t User1 t User2 t Off • POP : Optimized for R&B, Soul and Country music. • CLASSIC : Optimized for orchestral music. • ROCK : Optimized for Hard Rock and Heavy Metal music. • JAZZ : Sweet sound with soft feeling. • VOCAL : Powerful realism with strong sound quality. • SALSA : Reproduces salsa music acoustics. • SAMBA : Reproduces samba music acoustics. • USER1 : Use the menu to set the sound level you want. • USER2 : Use the menu to set the sound level you want. You can adjust each sound level to your preference. Once you select a USER mode and then make an adjustment, it automatically stored for the currently selected USER mode. Refer to the “Adjusting the sound level” on the page 11 10 Adjusting the sound level 1 Press SEL (MENU/SEL on the remote control) repeatedly to select the mode you want to adjust from volume, bass, middle, treble, balance and fader. The indicator lights up in the following order. VOL t BAS t MID t TRB t BAL t FAD 2 Rotate the MUTE/PWR (Press VOLUME on the remote control) to adjust the sound quality. Indication Turn right Turn left VOL Increase the volume level. Decrease the volume level. BAS Increase the bass level. Decrease the bass level. MID Increase the middle level. Decrease the middle level. TRB Increase the treble level. Decrease the treble level. BAL Decrease the level of the Decrease the level of the right left speaker(s). speaker(s). FAD Decrease the level of the front Decrease the level of the rear speaker(s). speaker(s). Note When EQ or XDSS+ is set to “Off”, you can adjust the sound level (BAS, MID, TRB) settings. XDSS+ (Extreme Dynamic Sound System) 1 Press and hold EQ/XDSS XDSS+ : Improves the treble, bass sound. 2 To cancel press and hold EQ/XDSS again. AUX operation Playing an Auxiliary Equipment You can connect Auxiliary Equipment to this unit. Connect one to the external device jack using the line input cable (not supplied), and the other to the AUX input jack on the control panel. Auxiliary input MP3 Player, etc Line input cable 11 1 Press SOURCE to select the AUX as source. AUX IN appears in the display. 2 Turn on the connected Auxiliary Equipment and start playing the source. 3 Adjust the volume. Note • Before operating the Auxiliary Equipment using the following procedure, select the external input correctly. (Refer to the page 11 for details.) • If the input level of the Auxiliary Equipment connected to the AUX input jack is not high enough, adjust the input level properly. (Refer to the page 11 for details.) Radio operation Listening to radio stations 1 Press SOURCE to select the tuner. 2 Press the BAND repeatedly to select a band. The indicator lights up in the following order. FM1 t FM2 t FM3 t MW(AM) 3 Auto Seek : Press I II/i ii (?m m/M M? on the remote control). When a station is received, searching stops. Manual Seek : Press and hold I II/i ii (?m m/M M? on the remote control) until “MANUAL” appears, and then press it repeatedly. The frequencies move up or down step by step. Storing and recalling broadcast frequencies You can easily store up to 6 broadcast frequencies for later recall at the touch of a button. 1 Press BAND to select desired band you want to store. 2 Select the desired frequency. 3 Press one of preset buttons 1-6 and hold until the beep sound. The number you have pressed will flash in the preset number indicator and then remain lit. The selected radio station frequency has been stored in memory. 4 Repeat steps 1-3 to preset other stations. The next time, you press the same preset button, the radio station frequency is recalled from the memory. Note • Up to 18 FM stations, 6 for each of three FM bands and 6 MW(AM) stations can be stored in the memory. • When a station is stored on the preset numbers on which another station of the same band has already been preset, the previously preset station is automatically erased. Auto search memory This function lets you automatically store the 6 strongest broadcast frequencies. 1 Press U UU/AS until “A/S” appears. The six strongest broadcast frequencies will be stored under preset button 1-6 in the order of their signal strength. 2 To cancel, press U UU/AS. To scan the preset stations Press u uu/PS. each preset station appears. To cancel, press u uu/PS. To tune in the preset stations Press BAND to select the desired band and press the desired preset button 1-6. The preset station of the preset button 1-6 is displayed and the preset station is received. 12 RDS operation RDS Display options In normal RDS operation the display will indicate the station name. Pressing DISP enables you to cycle through the various data types in the following sequence: CT t FREQUENCY t PTY t RT t PS • CT (Time controlled by the channel) • PTY (Programme type recognition) • RT (Radio text recognition) • PS (P...