Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
c Time data type indicators One of the three indicators (COUNTER, U-BIT, or TC) lights to indicate the type of time data currently shown in the time counter display. COUNTER: Count value of the time counter U-BIT: User bit data TC: SMPTE time code (for DSR-DR1000A) or EBU time code (for DSR-DR1000AP) d DVCAM indicator This stays lit. e KEY INHI (key inhibit) indicator Lights when the control mode selection switch is set to KEY INHI. f REC INHI (recording inhibit) indicator Lights when the REC INHIBIT menu item (see page 62) is set to ON. g Disk end alarm indicator Starts flashing when the remaining capacity of the disk is for about 2 minutes. h REPEAT (repeat playback) indicator Lights when the REPEAT MODE menu item (see page 61) is set to ON to enable the repeat playback function. i Time counter display Indicates the count value of the time counter, time code, VITC, or user bit data depending on the settings of the Location and Function of Parts COUNTER SELECT button and the TC SELECT menu item (see page 65). Also used to display error messages, edit data, setup menu data, etc. j Remote mode indicators REMOTE: Lights when the Control mode selector is set to REMOTE to remote control the unit from either an editing control unit connected to the REMOTE IN (R)/ OUT (P) connectors or equipment connected to the S400(i.LINK) connector. 9P: Lights when the REMOTE I/F menu item (see page 69) is set to 9PIN. i.LINK: Lights when the REMOTE I/F menu item (see page 69) is set to i.LINK. k VITC indicator Lights when VITC is being read or recorded regardless of the data shown in the time counter display. l PB Fs (playback audio sampling frequency) display During playback, this indicates the playback audio mode in which the disk being played back was recorded. 48K indicator: Lights during playback of material recorded in 2-channel mode (48 kHz). 32K indicator: Lights during playback of material recorded in 4-channel mode (32 kHz). m REC MODE (audio recording mode) display This indicates the audio recording mode currently selected with the REC MODE menu item (see page 68). 2CH indicator: Lights in 2-channel mode (48 kHz). 4CH indicator: Lights in 4-channel mode (32 kHz). 2 Video/audio input setting section INPUT SELECT CH1 1/2 CH2 3/4 3 CH2 3/4 button 2 CH1 1/2 button 1 VIDEO button a VIDEO button Each press of this button cycles through the following input video signal selection options. • Composite video signal input to the VIDEO IN connector • S-video (separated Y and C) signals input to the VIDEO IN connectors •Y, R.Y and B.Y component video signals input to the VIDEO IN connectors • SDI video signal input to the SDI IN connector • Video test signal (selected with the INT VIDEO SG menu item (see page 66) generated by the internal signal generator • Digital video/audio signal (DV format, complied with i.LINK) connected to the S400(i.LINK) connector The selection made with this button is indicated by the i.LINK/VIDEO indicators in the INPUT signal display section (see page 14). Note When the video input is set to the i.LINK, pressing either the CH1 1/2 button or CH2 3/4 button changes the setting to COMPOSITE. Reset the video input. b CH1 1/2 (audio channel 1 or 1/2) button Each press of this button cycles through the following input audio signal selection options for audio channel 1 (when in 2-channel mode) or for audio channels 1 and 2 (when in 4-channel mode). • Analog audio signal input to the AUDIO IN 1/3 connector • Digital audio signal in AES/EBU format input to the AUDIO (AES/EBU) IN 1/2 connector • SDI audio signal input to the SDI IN connector • Audio test signal (selected with the INT AUDIO SG menu item (see page 69) generated by the internal signal generator The selection made with this button is indicated by the AUDIO CH-1 1/2 indicators in the INPUT signal display section (see page 14). When analog audio is selected, the signal input to the AUDIO IN 1/3 connector is recorded either on channel 1 (when in 2-channel mode) or on channels 1 and 3 (when in 4-channel mode). That is, in 4-channel mode, the same analog audio signal is recorded on channels 1 and 3. Using the REC/PB LEVEL control knobs with the VARIABLE switch set to REC, it is possible to adjust the audio levels on the two channels separately. You can switch the audio recording mode with the REC MODE menu item (see page 68). The selection is indicated by the REC MODE display on the front panel. c CH2 3/4 (audio channel 2 or 3/4) button Each press of this button cycles through the following input audio signal selection options for audio channel 2 (when in 2-channel mode) or for audio channels 3 and 4 (when in 4-channel mode). • Analog audio signal input to the AUDIO IN 2/4 connector • Digital audio signal in AES/EBU format input to the AUDIO (AES/EBU) IN 3/4 connector • SDI audio signal input to the SDI IN connector • Audio test signal (selected with the INT AUDIO SG menu item (see page 69) generated by the internal signal generator Chapter 1 Overview...
Ce manuel est également adapté pour les modèles :Lecteur DVD - DSR-DR1000AP (1.89 mb)