Évaluations - 4, GPA: 3.5
(
)
)
|
Facilité d'utilisation
EX I T SETUP OFF OFF NORMAL 2CH DIGITAL INTERFACE SETUP HDMI/DVI BLACK LEVEL HDMI AUDIO SETUP DENON LINK IEEE1394 DECISION: ENTER BUTTON SELECT : 2 Use the • and . cursor buttons to select the desired setting, then press the ENTER button. HDMI/DVI BLACK LEVEL Switches the digital RGB video level (data range) of the HDMI and the DVI-D terminals. HDMI AUDIO SETUP Use this to adjust for the audio signals from the HDMI terminal. DENON LINK Use this to output digital signals from the DENON LINK terminal. IEEE1394 Use this to output digital signals from the IEEE1394 terminal. Remote control unit Remote control unit DECISION: ENTER BUTTON SELECT : DIGITAL INTERFACE SETUP EX I T SETUP HDMI/DVI BLACK LEVEL NORMAL ENHANCEDHDMI AUDIO SETUP DENON LINK IEEE1394 3 Use the • and . cursor buttons to select the desired setting, then press the ENTER button. q When “HDMI/DVI BLACK LEVEL” is selected: NORMAL (Factory default) Signals are output from the HDMI and the DVI-D terminals with a digital RGB video level (data range) of 16(black) to 235(white). ENHANCED Signals are output from the HDMI and the DVI-D terminals with a digital RGB video level (data range) of 0(black) to 246(white). . When the HDMI and the DVI-D terminals are connected , the black may seem to stand out, depending on the TV or the Monitor you are using. In this case, set this to “ENHANCED”. . When select “HDMI Y Cb Cr” under “HDMI/DVI SELECT”, will have no effect. (See page 53.) 32 ENGLISH 3 w When “HDMI AUDIO SETUP” is selected: 2CH (Channel) (Factory default) The audio signals are output from the HDMI terminal with a down- mixed to 2 channel. MULTI(NORMAL) The multi-channel audio signals are output from the HDMI terminal with a bit-stream. MULTI(LPCM) The multi-channel audio signals are output from the HDMI terminal with a linear PCM. B When “MULTI (LPCM)” is selected, use the • and . cursor buttons to select the item to be set, then press the ENTER button. SPEAKER CONFIGURATION Use this to select the types of the different speakers. CHANNEL LEVEL Use this to adjust the output level of the different speakers. DELAY TIME Use this to set the distance from the different speakers to the listening position. . To exit the SPEAKER SETUP mode. Use the . cursor button to select “DIGITAL INTERFACE SETUP” then press ENTER button. B When “SPEAKER CONFIGURATION” is selected, use the • and . cursor buttons to select the speaker to be set then press the ENTER button. • The type of speaker used for the front speakers, center speaker, subwoofer and surround speakers can be set. Use the • and . cursor buttons to select the speaker type, then press the ENTER button. LARGE Select this when a large speaker is connected. SMALL Select this when a small speaker is connected. NONE Select this when no speaker is connected. YES Select this when a subwoofer is connected. NO Select this when no subwoofer is connected. • When “CROSSOVER” is selected: 40 Hz, 60 Hz, 80 Hz (Factory default), 100 Hz, 120 Hz, set the frequency of cross over. . Press the RETURN button to return to the “HDMI SPEAKER SETUP” menu. B When “CHANNEL LEVEL” is selected, use the • and . cursor buttons to select the speaker to be adjusted, then use the 0 and 1 cursor buttons to set the level. TEST TONE • Use the 0 and 1 cursor buttons to select auto or manual. Adjust so that the volume of the test tones output from the different speakers sounds the same. • The volume level output from the front speakers (left and right channels), center speaker, surround speakers (left and right channels) and subwoofer can be adjusted. • The volume level can be adjusted between 0 and -10 dB in steps of 1 dB. . Press the RETURN button to return to the “HDMI SPEAKER SETUP” menu. DECISION : ENTER BUTTON SEL ECT : DIG ITAL INTERF ACE SETUP EX I T SETUP HDMI/ DVI BLACK L EVEL 2CH MULTI(NORMAL) MULTI(LPCM) HDM I AUDIO SETUP DENON LINK IEEE1394 HDMI SPEAKER SE TUP SPEAKER CONF I GURAT I ON CHANNEL L EVEL DELAY TIME DIGITAL INTERFACE SETUP DECISION : ENTER BUTTON SEL ECT : HDMI SPEAKER SETUP SPEAKER CONF I GURAT I ON FRONT SP CENTER SP SUBWOOFER SURROUND SP CROSSOVE R LARGE LARGE YES LARGE 80Hz DECISION : ENTER BUTTON SEL ECT : HDMI SPEAKER SETUP CHANNEL LEVEL DECISION : ENTER BUTTON SEL ECT : TEST TONE FRONT LCH CENTER FRONT RCH SURROUND RCH SURROUND LCH SUBWOOFER OF F 0dB 0dB 0dB 0dB 0dB 0dB Remote control unit Remote control unit The display depends on the connected device. (Indicates whether or not speakers are connected) 33 ENGLISH 3 B When “DELAY TIME” is selected: With 5.1-channel surround sound, ideally the distance between the listening position and all the speakers aside from the subwoofer should be the same. The delay time setting can be used to make the sound from the different speakers reach the listening position at the same time. Use the • and . cursor buttons to select the setting item, then press the ENTER button. B When “DISTANCE” is selected: METERS (when the 0 cursor button is pressed): The unit of distance is set to met...