Évaluations - 2, GPA: 4.5
(
)
)
|
Facilité d'utilisation
Included Hardware: (2) 3x20mm screws (1) Double sided adhesive pad The wireless door chime kit has two components: Battery Operated Chime (Receiver) PushButton (Transmitter) Plugs into 120V outlet Battery included Chime Tune Setting All wireless chimes may have more than one pushbutton. The chime tune for each push button is set withdip switches 1-3. Located inside the push button. Single Push Button Kit: If you purchased a kit with asingle push button, the chime tune will be set to DingDong from the factory. Dual Push Button Kit: If you purchased a kit with twopush buttons, one push button will be set to Ding Dongand the other push button will be set to Westminsterfrom the factory. The following instructions explain how to change thetune on any wireless push button. 1. Remove the cover from the push button -see wireless push button battery. 2. Remove the battery from the push button transmitter. 3. Locate the 3 dip switches shown below. 4. Select the desired chime sound from the table below. Chime Sound Table Position 1 2 3 Westminster ON OFF OFF Ding Dong Knock OFF OFF ON OFF OFF ON Bronze Chime ON ON OFF Cuckoo Clock ON OFF ON FoghornGong OFF ON ON ON ON ON Pushbutton House Code Jumpers Chime Dip Switches Pushbutton Dip Switches and Jumpers Setting The House Security Code Each chime component has 4 jumpers for setting thehouse security code. In most cases you will not needto change the factory settings for the house securitycode. If your chime activates intermittently or does notwork at all, you may be able to solve the problem bychanging your security code. Pushbutton House Code Jumpers Chime DipSwitches The chime and pushbutton must be set to the samehouse security code for the combination to operatetogether. 1. Remove power from the chime. 2. To remove the batteries from the pushbutton, openthe pushbutton case as shown below. Pushbutton House Code Jumpers Chime DipSwitches Pushbutton Jumpers 3. Locate the House Security Code door and screwlocated on the back of the Chime. Remove the screw and take off the door. 4. Locate the chime and pushbutton jumpers shownabove. 5. To change the house code, add or remove jumpersas needed. It is recommended to change only onejumper at a time and then test the system for properoperation. The jumpers on the chime and pushbuttonmust match exactly. Wireless push button battery To install or replace the battery in the wireless pushbutton. 1. Remove the back cover of the push button. 2. InstalltheA23(12volt)batterywiththenegativeside of the battery (-) toward the spring and thepositive side of the battery (+) toward the positivebattery holder as shown below. 3. Replacebackcoverasshownbelow. Push Button Mounting InstructionsNote:Avoid mounting on metal surfaces, as it mayresult in a reduced range of transmission. Do not mountin an area where exposed to direct rain. a. Removing the back cover b. Replacing the back cover Mounting Push Button 1. Pushbuttonsaretypicallymountedatthesameheightasthedoorknoborhandle(between36”and 44” above the floor). 2. Before mounting, choose a mounting location thatis not farther than 150 feet from the chime unit location. Not further than 150 feet 3. Beforeplacingthepushbuttonwhereyouwouldlike to mount it, place the chime as close to final position aspossible.Testtheoperationbeforedrilling.Ifitworks,mountthepushbutton.Ifitdoesnotwork, seeTROUBLESHOOTING. 4. Usebackcoverofpushbuttonasatemplatetomarktwoscrewholes. 4568 5. Drill two holes with 1/16” size drill in markedlocations. 6. Secure back cover to the mounting surface with twosupplied mounting screws. 7. Install the supplied 12V battery observing properpolarity. (see battery installation section) 8. Press front housing onto back cover. 9. Test operation. If the chime does not work, see TROUBLESHOOTING. If you do not want to drill holes in your door frame, youcan use the supplied double sided tape for installation. 1. Clean all mounting surfaces with a 50/50 mixture ofisopropyl alcohol. 2. Remove the backing from one side of the doublesided tape and press the exposed side against theback plate of the push button. 3. Remove the other backing strip and press theexposed side against the door frame where you wantthe button installed. PowerIndicatorOn/OffSwitch Operation 1. Plugthechimeintoa120VACoutletandslidethepowerswitchtothe“On”positiontoturnonthechime.TheredLEDpowerindicatorwilllight. 2. Gently press transmitter button to sound chime. Troubleshooting Chime doesn’t work: 1. Make sure push button switch is depressed and heldfor at least 1 second. 2. Make sure house code switches 1-4 on chime and push button match exactly. 3. Verify battery orientation in push button. 4. Try fresh batteries. 5. Make sure chime is not farther than 150 feet awayfrom push button. 6. Ensure push button is not mounted on metal, near metal studs, or near the floor. 7. Try a new location for the chime. Functional range may be adversely affected by one or more of the following factors: weather, radio frequency interfe...