If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. 2. Plug-in the doorbell chime. Chime Volume Control 1. Set the chime volume on the back of the plug-in chime, if desired. 3. Before mounting, test the doorbell range. Plug-in the chime where you want to mount it and temporarily place the doorbell button on the doorjamb. Press the doorbell button. Access Door Ope

If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. 2. Plug-in the doorbell chime. Chime Volume Control 1. Set the chime volume on the back of the plug-in chime, if desired. 3. Before mounting, test the doorbell range. Plug-in the chime where you want to mount it and temporarily place the doorbell button on the doorjamb. Press the doorbell button. Access Door Ope

Snap the front of the button back on. When attaching the doorbell button using the double sided tape, make sure the surface of the door jamb or wall is clean. © 2003 DESA Specialty Products™ 595-5707-04 The chime can be mounted by using the 3 holes in the back of the case, or by using 2 screws with the keyholes. Chime Back Case Keyhole Mounting Chime Back Case Mounting Close Chime Case From Bottom Snap the front of the chime case back on. Start with the bottom edge of the case aligned wi

2. Install the 3 alkaline "D" batteries. Make sure the batteries are oriented properly. 3. Before mounting, test the doorbell range. Put the chime where you want to mount it and temporarily place the doorbell button on the doorjamb. Press the doorbell button. Operation Press the doorbell button to verify that the doorbell and chime work properly. If the chime does not sound see the Troubleshooting guide on page 4. 4. Mount the doorbell button and chime. Use either screws or double sided tape to

It is recommended to only change one jumper at a time and then check to see if system is functioning properly. Note: Jumpers in positions 1 through 7 must be exactly the same for both the transmitter and chime for this system to function. -4-595-5345-06 Tune Settings Your Heath®/Zenith wireless chime has different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note) (Available on selected Heath®/Zenith chimes). The factory setting is for the Ding-Dong tune (or Wes

In typical use, alkaline batteries will last up to three years. 2. Install 3 alkaline "D" batteries. Make sure batteries are oriented properly. 1. Install alkaline type A23 12 volt push button battery. Remove back of case by pushing in tab on bottom with a small screwdriver. Make sure battery is oriented properly (see page 3). 3. Test range. Temporarily position chime and push button where you want them mounted. Press push button to verify chime and push button work properly. If chime does not s

In typical use, alkaline batteries will last up to three years. Battery Chime Volume 1. To open the chime case: press in the catch on the bottom of the chime and lift the case open. 2. Install the 3 alkaline "D" batteries. Make sure the batteries are oriented properly. 3. Before mounting, test the doorbell range. Put the chime where you want to mount it and temporarily place the doorbell button on the doorjamb. Press the doorbell button. Operation Press the doorbell button to verify that the doo

Back of Chime Tune Setting (Not used on all models) Note: Some models might require the use of tweezers to remove and replace the jumpers. 595-5649-05 -3 Troubleshooting Chime does not sound: • Make sure push button and chime codes are the same (See pages 2 and 3). • Check orientation of push button battery (See page 3). • Check push button battery charge, replace if necessary. Batteries seem OK, but the chime does not work when installed: • Do not mount chime or push button on metal or near met

Sound travels farthest with the fewest obstacles. Do not place over heat source; i.e., radiator, heater, or stove. At the chosen location drill two small pilot holes 3 1/4" apart in the vertical plane. The chime cover is a push fit onto the base. Remove chime cover to expose base. Position base and mount in place using screws supplied, key-hole shaped slot at the 1 32 Base Plate Chime Cover top (see Figure 1). Figure 1 WIRING THE CHIME To Push Button A. Battery Operation. Do not use with lighted

• Battery powered push button - No wires to run. • 128 selectable codes allow more than one chime system in the same house. • LED lighted push bar (see Lighted Push Bar Feature). Lighted Push Bar Feature This ACE® wireless push button contains a LED (Light Emitting Diode) that will illuminate in dark conditions so the push button will be more visible for your guests. This (patent pending) technology and built-in photocontrol will allow the light intensity of the push button LED to increase as th