Log:
Téléchargements : 7   Taille : 1 mb   Fabricant : Ives  
Catégorie : Portes et fenêtres
@name

Téléchargements : 14   Taille : 437 kb   Fabricant : Ives  
Catégorie : Portes et fenêtres
@name

780 Door Chime DWG # 2375 Rev A, new drawing # 9/7/00 Tools Required: Hand or electric drill No. 2 point Phillips screwdriver 1 inch, 3/32 inch and 7/64 inch drills STEP 1 STEP 2 STEP 3 Mark horizontal reference line on OUTSIDE of door at convenient eye level (recommended 58 inches up from bottom of door). Mark vertical line on door centered from left to right. (See fig. 1) Align template reference lines with lines on door and mark location of 3 holes labeled "OUTSIDE ©" on door. Dril

Téléchargements : 0   Taille : 270 kb   Fabricant : Ives  
Catégorie : Portes et fenêtres
@name

CONNECT CABLE 6. SET DEVICE ADDRESS 7. SECURE & LOCK CASE AM/II f m KEYP AD IN :-f + o o o o o o © -9- 00 I I à à s s ¿> PWR | GND | DAT11 DATO | DVAL | CLK 0 AM- USE A SMALL SCREWDRIVER TO SET THE DEVICE ADDRESS SWITCH FOR LOCAL POWER, DISCONNECT RED WIRE FROM "PWR" CONNECTION ON AM-KP AND CONNECT EXTERNAL 12 VDC SUPPLY (+ TO PWR & - TO GND) NOTE: AM/II * MUST BE CONNECTED TO AM-KP "GND" 8. PROGRAM SYSTEM PROGRAM THE AM/II TO CONFIGURE THE KEYPAD(S) AND SET THE ENTRY CODES R

Téléchargements : 4   Taille : 196 kb   Fabricant : Ives  
Catégorie : Portes et fenêtres
@name

Not doing so may result in improper installation and void the manufacturer’s guarantee. These hinges have a permanent, factory applied lubricant. Removal or alteration of this lubricant, anodizing or painting of the product in the field will void the guarantee. INSTALLATION NOTES Reinforcing and Rivet nuts: No reinforcing is necessary except on extremely high frequency, extremely heavy or extra-wide doors. Rivet nuts are required in the frame and door when door weight exceeds 450 pounds (up t

Téléchargements : 7   Taille : 196 kb   Fabricant : Ives  
Catégorie : Portes et fenêtres
@name

.. .... Ingersoll Rand © 2006 Ingersoll-Rand Company Limited Security Technologies 829168-00 INSTALLATION Q Mark frame hole locations. A. Open hinge and place frame leaf flat against surface of frame leaving 1/8” gap between top of hinge and frame header. Hinge lip should be held tight against the frame face from top to bottom. B. Mark all hole locations on frame using center punch provided. C. Drill all holes using #13 (.185”) or 3/16” (.188”) drill for metal frame. For wood frame us

Téléchargements : 0   Taille : 94 kb   Fabricant : Ives  
Catégorie : Portes et fenêtres
@name

Position jamb bracket 1/4" in from door and fasten to doorframe (see illustration below) .Open side of bracket must be facing screen or storm — 2. Slide the "hold open" washer onto rod. Use short connecting pin to connect closer to jamb bracket. The “hold open" washer should be placed over lugs against closer tube (see illustration below). This will provide proper tension for installation and should not be adjusted until installation is complete. 3. Use long connecting pin to attach door brack

Téléchargements : 4   Taille : 85 kb   Fabricant : Ives  
Catégorie : Portes et fenêtres

Téléchargements : 5   Taille : 85 kb   Fabricant : Ives  
Catégorie : Portes et fenêtres

Téléchargements : 3   Taille : 73 kb   Fabricant : Ives  
Catégorie : Portes et fenêtres
@name

Use sex bolts on metal doors not reinforced. Recommended mounting is stop on door. Remove and discard safety net screw except lor inverted. top of door applications. 1: Mount back plate with centerline 3H" from latch edge of door and top of plate 5" from bottom of door, as indicated in illustrations at right and below. Locate screw holes by using back plate as template. Use #8 x 1" flat head sheet metal screws for wood doors, or #8-32 x W flat head machine screws for reinforced metal doors. 2:

Téléchargements : 0   Taille : 66 kb   Fabricant : Ives  
Catégorie : Portes et fenêtres
@name

Since ¡876, H.B. li'es quality hardware has helped build the most distinguished homes In America. APARTMENT DOOR KNOCKER WITH VIEWER FOR USE ON EXTERIOR OR INTERIOR DOORS OF HOMES, CONDOMINIUMS, APARTMENTS AND OFFICES. INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Drill, 1/4" and 1/2" drill bits. awl and screwdriver 1. Position template (right) centered from side to side 60" above threshold. Tape template to outside of door. 2. Mark centers with awl (or nail) and drill holes (A) with 1/4” d





catégories