Évaluations - , GPA: ( )

Instructions Olympus, Modèle FL-300R

Fabricant : Olympus
Taille : 6.45 mb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Information for Your Safety IMPORTANT SAFETY INSTRUCTIONS When using your photographic equipment, basic safety precautions should always be followed, including the following: • Read and understand all instructions before using. • Close supervision is necessary when any fl ash is used by or near children. Do not leave fl ash unattended while in use. • Care must be taken as burns can occur from touching hot parts. • Do not operate if the fl ash has been dropped or damaged - until it has been examined by qualifi ed service personnel. • Let fl ash cool completely before putting away. • To reduce the risk of electric shock, do not immerse this fl ash in water or other liquids. • To reduce the risk of electric shock, do not disassemble this fl ash, but take it to qualifi ed service personnel when service or repair work is required. Incorrect reassembly can cause electric shock when the fl ash is used subsequently. • The use of an accessory attachment not recommended by the manufacturer may cause a risk of fi re, electric shock, or injury to persons. SAVE THESE INSTRUCTIONS Thank you for purchasing this Olympus product. To ensure your safety, please read this instruction manual before use, and keep it handy for future reference. p (g Names of parts (Fig. p )p. 3) 1 Light-emitting area 5 AUTO CHECK 2 Lock release lamp button 6 ON/OFF button 3 Lock pin 7 W knob 4 TEST button/ 8 RC switch CHARGE lamp 9 Remote sensor Continuous firingg The flash may become hot when fired many times in succession, resulting in damage or malfunction. The flash should be fired no more than 10 times in succession at intervals of 6 seconds, after which it should be left unused for at least 10 minutes. x Notes AAA (R03) manganese batteries cannot be used. g Loading batteries 1 Open the battery compartment cover. 2 Insert the batteries with correct +/– polarity. Battery compartment Battery compartmentBattery compartment cover covercover Preparing a battery ( p g y)yp(sold separately) Choose from the below batteries: • AAA (R03) alkaline batteries (x 2) 3 Close the battery compartment cover. • AAA (R03) NiMH batteries (x 2) EN 7 8 EN Attaching to the camera x Notes Confi rm that both the camera and electronic fl ash are off. Attaching or removing the electronic fl ash while either the fl ash or the camera is on may result in malfunction. 1 2 1 Remove the camera hot shoe cover and slide the fl ash securely into the hot shoe until it clicks into place (1). Do not attach this fl ash with the built-in fl ash raised, or the built-in fl ash may get broken. Remove the fl ash while pressing the lock release button (2). If the camera has an external fl ash connector, a fl ash bracket and bracket cable (sold separately) can be attached. • g Turning on the electronic flash Attach an electronic flash to the camera, and then turn the camera on. 1 Press and hold the ON/OFF button until any lamp lights. • Press the ON/OFF button again to turn the power off. • Press the TEST button to fire a test flash when the CHARGE lamp lights. TEST button/ ON/OFF CHARGE lamp button • Replace the batteries if the CHARGE lamp does not light after: 30 seconds (Alkaline batteries) 10 seconds (NiMH batteries) • If the CHARGE lamp and AUTO CHECK lamp blink simultaneously, batteries are running low. Replace the batteries. • If no operations are performed for about 15 minutes, the flash will enter sleep mode to save power. The flash will also enter sleep mode whenever the camera enters sleep mode. If no operations are performed for approximately 60 minutes more, the flash will turn off automatically. Press the ON/OFF button to turn it on. EN 9 gShooting Shooting According to the flash mode setting of the camera, shooting in TTL-AUTO mode or MANUAL mode is available with this flash. 1 Set the RC switch to “OFF”. 2 In accordance with the intended use, set the fl ash mode of the camera. For details, refer to the instruction manual of the camera. RC switch MANUAL mode is not available for some cameras. • In TTL-AUTO mode: When flash activation has been performed correctly, the AUTO CHECK lamp blinks for about 5 seconds after the shooting. • In MANUAL mode: Adjust camera settings (ISO sensitivity and aperture value) based on the distance to subject and then shoot. Shooting distance (m) = Guide No. (ISO100) x ISO sensitivity coefficient . Aperture value Available shooting range (Table P.4) ISO sensitivity coefficient ISO sensitivity 25 50 100 200 400 800 1600 3200 6400 Coefficient 0.5 0.71 1.0 1.4 2.0 2.8 4.0 5.6 8.0 • When using a flash, flash light may be blocked by the lens body, lens hood, etc. • When the shooting distance is closer to 1m, using the wide panel is recommended not to control the flash volume too much. 10 EN EN 11 Wide angle Use the wide panel for shooting when the lens focal length is wider than 9 mm to 14 mm. 1 Slide the W knob to the W side. Folding This fl ash can be bent approx. 30 degrees in front (1) and 60 degrees in rear (2). It also can be folded in front t...