Évaluations - , GPA:
(
)
)
Fabricant : Echo
Taille : 466.11 kb
Nom Fichier : 99944200475e_012009.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
3. DRIVE ShAFT ASSEMBLy - Contains a specially designed liner and the flexible drive shaft. 4. WhEEL - Adjustable up/down, sets depth of blade. A B D Parts Required: PAS or SRM-SB Power Head w/Shaft & Coupling. 1. Set Power Head/Shaft Assembly on a level surface. 2. Pull locator pin (A) out, and turn counter-clockwise 1/4 turn to lock-out position. 3. Remove vinyl cap from attachment drive shaft. 4. Remove cardboard spacer, if necessary. 5. Carefully fit attachment drive shaft assembly into coupler (B) to de- cal assembly line (C), making sure that the inner lower drive shaft engages into the square upper drive shaft socket. power head shafT/lower shafT assembly WARNING Do not perform maintenance or assembly procedures with engine running. The ECHO product you purchased has been factory pre-assembled for your convenience. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. ___ 1 -Power Edger Attachment ___ 1 -Operators Manual ___ 1 -Warranty Registration Card ___ 2 -Split Pins ___ 1 -Storage Hook Assembly ___ Assembly Tool (s) 1. BLADE - Rotates to provide cutting action. 2. DEBRIS ShIELD/FLAP -Mounted over the cutting attachment. Helps protect operator by deflecting debris produced during the edging operation. 3. DRIVE ShAFT ASSEMBLy - Contains a specially designed liner and the flexible drive shaft. 4. WhEEL - Adjustable up/down, sets depth of blade. A B D Parts Required: PAS or SRM-SB Power Head w/Shaft & Coupling. 1. Set Power Head/Shaft Assembly on a level surface. 2. Pull locator pin (A) out, and turn counter-clockwise 1/4 turn to lock-out position. 3. Remove vinyl cap from attachment drive shaft. 4. Remove cardboard spacer, if necessary. 5. Carefully fit attachment drive shaft assembly into coupler (B) to de- cal assembly line (C), making sure that the inner lower drive shaft engages into the square upper drive shaft socket. power head shafT/lower shafT assembly WARNING Do not perform maintenance or assembly procedures with engine running. assembly NOTE Earlier model Power Heads may have shorter couplings. Short couplings fit flush to decal point (E). New couplings are 4-3/4 in. long, and fit flush to line (C). NOTE Lower bearing housing and head assembly must be in line with the engine. 6. Rotate locator pin (A) 1/4 turn clockwise to engage lower shaft hole. Insure locator pin is fully engaged by twisting lower drive shaft. Locator pin should snap flush in coupler. Full engagement will prevent further shaft rotation. 7. Secure lower shaft assembly to coupler by tightening clamping knob (D). operaTIon C D E WARNING Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Operating Techniques 1. Before edging, water the area to soften the ground to make edgingeasier. Before edging, check the area and remove all obstacles and objects that could be thrown. 3. Plan to edge regularly to make it easier to keep a neat edge and toavoid having to make more than one pass. NOTE Blade depth may have to be adjusted due to differences in height between the hard surface and the top of the grass. oPerAtor's mAnuAl 94. Loosen adjustment knob and adjust the blade's depth of cut to produce a fine cut between sidewalk and grass using a minimumblade depth, usually with about 13 mm (1/2 in.) of the blade into the ground. Tighten adjustment knob. 5. Before edging, plan your direction of travel so that the unit will al- ways be positioned on your right side and so that you walk on a hard surface whenever possible. 6. Hold edger as shown. WARNING Before edging, be sure to read and understand the entire Operator'sManual to avoid the chance of serious injury. 7. When starting to edge, run the engine at full throttle, and lower the blade gently into the ground, being careful not to hit the concretewith the blade. 8. Don't force the blade. Only move forward as the blade will allow. WARNING The complete unit, specifically the drive shaft assembly and mufflerexhaust area may become very hot during use. Avoid contact during and immediately after operation, otherwise serious personal injurymay result. 1/2 in. INCREASE DEPTH WHEEL ADJUSTMENT KNOB DECREASE DEPTH WARNING Never adjust blade height with engine running, otherwise serious personal injury may result. maInTenanCe Your ECHO unit is designed to provide many hours of trouble-free service. Regular scheduled maintenance will help your unit achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maint...