Évaluations - 4, GPA: 4.8
(
)
)
|
Facilité d'utilisation
Slide seat to desired setting and fully tighten seat adjustment knobs. Caution: DO NOT Operate mower unless seat adjustment knobs are fully tightened. Page 1 of 13 REMOVING THE BODY: 1. Both the 4421 & 4422 use a two piece body. The upper body can be raised up and back, and also tilted forward to expose the transaxle. 2. To remove upper body, lift up and fold forward. Disconnect throttle cable P/N 4679 from engine. Disconnect wiring harness by simply pulling plug apart. Then clip wire ties soharness is loose from seat bracket. Next remove cotter key P/N 3052 from upper body mounting pin P/N 1460. Then hold upper body and remove pin P/N 1460. 3. Reverse above procedure to reinstall. ADJUSTMENT OF MOWER DECK DRIVE BELT: No adjustment necessary! The spring loaded idler pulley maintains proper tension throughout belt life. REMOVING THE MOWER BLADE: 1. Secure mower blade P/N 8688 from turning. 2. Observe blade position when removing. 3. Remove blade bolt P/N 3268, and blade washer P/N 6260. 4. To reinstall, reverse above procedure. Tighten blade bolts to 60 ft. Ibs. of torque. WARNING: Sharp edges on blade can cause injury! Caution should be exercised when service is required on the blade. REMOVING THE MOWER DECK: 1. Remove mower deck drive belt P/N 6111 by pulling idler pulley P/N 1687 away from belt and remove belt from the rear pulley. 2. Remove the two clevis pins P/N 3072 from the L -rods at rear of deck and slide free from slots. 3. Remove the clevis pin P/N 3072 from the lift linkage at the front of deck. 4. Remove cotter pin from shaft P/N 1332 located at front of mower deck on slide plates welded at battery box. Slide shaft free. 5. Raise front of mower and roll it free of mower deck assembly. 6. To install deck, reverse above procedure. Page 2 of 13 MOWER BLADE OPERATION: 1. To start mower blades, pull up slightly on blade drive switch handle and move it forward to the "ON" position. 2. To stop mower blades, move switch handle to the "OFF" position. SAFETY CHECKS IMPORTANT-PERFORM SAFETY CHECKS AFTER MAKING ANY REPAIRS OR ADJUSTMENTS 1. After reassembly, while seated on mower, attempt to start engine with mower deck engaged. Engine should not start. If engine does start, return the mower to an Au thorized Dixon dealer for adjustment or repair. 2. Disengage mower deck and start engine. With the operator in the normal seated position, engage mower deck and remove weight from seat. The engine should stop. If the engine does not stop when operator ri ses from seat, return the mower to an Authorized Dixon dealer for adjustment or repair. 3. Engage, then disengage mower blade in each cutting height. Insure that blade disengages and comes to a stop within (5) seconds in each height position. If blade do es not disengage properly, contact your Authorized Dixon dealer. CAUTION: DO NOT OPERATE MOWER IF ANY SAFETY FEATURE IS NOT FUNCTIONING CORRECTLY Parking Brake Adjustment: 1. Adjustment points are located at rear of transaxle on each side. Remove roll pins from swivel fitting P/N 2172. Turn swivel fitting on brake rod P/N 5100 in, to tighten. Just enough to prevent brake from slipping when engaged. 2. Reinstall roll pin. CAUTION: Over tightening may cause premature wear on brake band P/N 5085. . Page 3 of 13 THE FOLLOWING INSTRUCTIONS ...
Ce manuel est également adapté pour les modèles :Tondeuse à gazon - TECHNICAL DATA BROCHURE ZTR 4421 (184.42 kb)