Évaluations - 2, GPA: 4.5
(
)
)
|
Facilité d'utilisation
Locate fully assembled grassbox onto 2 location points (G3) at the rear of the deck as illustrated in pic. H 4. Locate safety flap onto the top of the grassbox. Ensure the grassbox is securely located. • IMPORTANT ! AFTER FITTING ENSURE NO GAP REMAINS BETWEEN THE SAFETY FLAP AND THE GRASSBOX. • Removal is the reverse procedure. • For larger areas of grass where grass collection is not required you can use your lawnmower without the grassbox. Ensure the Safety Flap is fully closed. The design of the safety flap permits the cut grass to be discharged downward behind the machine. J grassbox empty grassbox full Visimo Only Grassbox Full Window (Visimo Only) • As the grassbox fills up, grass will be visible through the window (J). • When the window/grassbox is full it is time to empty the grassbox. Cutting Height Adjustment Cutting Height Adjustment (K) & (L) • Height of cut is adjusted by raising or lowering the Front and Rear Wheels. • There are five heights of cut on this product. • NOTE A medium height of cut is recommended for most lawns. The quality of your lawn will suffer and collection will be poor if you cut too low. HEIGHT OF CUT WHEELS POSITION Low Front position 2cm Rear position 2cm Low to Medium Front position 2cm Rear position 4cm Medium Front position 4cm Rear position 4cm Medium to High Front position 4cm Rear position 6cm High Front position 6cm Rear position 6cm K L 2cm 6cm 4cm M N R Starting and Stopping To Start your Lawnmower 1. Form loop in mains cable and push the loop through the slot. (M) 2. To secure, position loop over the hook and pull the cable back through the slot (N). 3. Connect plug to mains and switch on. 4. Tilt the handle downwards to slightly raise the front of the lawnmower and to reduce the risk of lawn damage whilst starting. The switchbox is provided with a lock-off button (P1) to prevent accidental starting. 5. Press and hold the lock-off button (P) on the switchbox, then squeeze one of the Start/Stop levers towards the upper handle (Q). 6. Continue to squeeze the start/stop lever towards the upper handle and release the lock-off button (R). 7. Lower the lawnmower to its proper operating position and commence mowing. • NOTE - There are two start/stop levers fitted. Either one can be used for starting the lawnmower. • IMPORTANT - Do not use the start/stop levers intermittently To Stop your Lawnmower 1. Release the pressure on the Start/Stop lever. P Q 1 How to Mow 1. Start mowing the edge of the lawn nearest to the power point so the cable is laid out on the lawn you have already cut. (S) 2. Mow twice a week during the growing season, your lawn will suffer if more than a third of its length is cut at one time and this may also result in poor collection. Do Not Overload Your Mower Mowing long thick grass may cause the motor speed to drop, you will hear a change in the motor sound. If the motor speed drops you may overload your lawnmower which may cause damage. When mowing in long thick grass a first cut with the cutting height set higher will help reduce the load. See Cutting Height Adjustment. Removing and Fitting the Blade Switch off, wait until the blade has stopped rotating and disconnect from the mains electricity supply BEFORE attempting to remove or refit the blade. Always handle the blade with care - sharp edges could cause injury. USE GLOVES. Removing the Blade 1. To remove the blade bolt, hold the blade firmly with a gloved hand and with a spanner, loosen the blade bolt by turning it anti-clockwise (S). 2. Remove the blade bolt, washer and blade.(S) 3. Inspect for damage and clean as necessary. 4. In the event of a blade becoming difficult to remove, insert a screwdriver (T1) into the hole (T2) to lock the drive, then use a spanner (13mm A/F) to loosen the blade bolt by turning the spanner anti-clockwise. Ensure the screwdriver is removed before atempting to turn on the machine. Renew your metal blade after 50 hours mowing or 2 years whichever is the sooner - regardless of condition. If the blade is cracked or damaged replace it with a new one. Fitting the Blade 1. Fit the blade to the shaft with the sharp edges of the blade pointing away from the shaft and you are able to read the text on the blade ‘This side to grass’ 2. Re-assemble blade bolt through the washer and the blade. 3. Hold the blade firmly with a gloved hand and tighten the blade bolt firmly with a spanner . Do not over tighten. S blade blade bolt washer T 1 2 Caring for your Lawnmower Cleaning • USE GLOVES • IMPORTANT:- It is very important that you keep your lawnmower clean. Grass clippings left in any of the air intakes or under the deck could become a potential fire hazard. 1. Remove grass from under the deck with brush. (V1) 2. Using a soft brush - remove grass clippings from all air intakes (V2), the discharge chute (V3) and the grass box (V4). 3. Visimo Only - Using a soft brush, remove grass clippings from the vision window (V5). 4. Wipe over the surface of your lawnmower with a dry cloth ...