|
Facilité d'utilisation
Keep clear of the discharge opening at all times as the rotating blade can cause injury. 4. Stop the blade when crossing gravel drives, walks or roads. 5. After striking a foreign object, stop the engine, remove the wire from the spark plug, and thoroughly inspect the edger for any damage. Repair the damage before restarting and operating the edger. 6. If the equipment should start to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of trouble. 7. Stop the engine whenever you leave the equipment, before cleaning the guard assembly, and when making any repairs or inspections. 8. Before cleaning, repairing or inspecting, make certain the blade and all moving parts have stopped. Disconnect the spark plug wire, and keep the wire away from the spark plug to prevent accidental starting. 9. Do not run the engine indoors. 10. Shut the engine off and wait until the blade comes to a complete stop before unclogging guard assembly. 11. Never operate edger without proper guards, plates or other safety protective devices in place. 12. Always operate the edger so that the protective guard guide is positioned between the walk and the rotating blade. Never allow the rotating blade to operate directly against concrete walk or drive. MAINTENANCE AND STORAGE 1. Check the blade and engine mounting bolts at frequent intervals for proper tightness. 2. Keep all nuts, bolts, and screws tight to be sure the equipment is in safe working condition. 3. Never store the equipment with gasoline in the tank inside of a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. 4. To reduce fire hazard, keep the engine free of grass, leaves, or excessive grease. I NOTE This unit is shipped WITHOUT GASOLINE or OIL. After assembly, see operating section of this manual for proper fuel and engine oil recommendations. Q j ASSEMBLY INSTRUCTIONS FIGURE 1 HOLE AND SLOT IN FRAME FIGURE 2 LOCK WASHER (G) SHOULDE\ BOLT (F) NOTE Any reference to right and left hand will be determined from behind the edger, in the operator's position. TOOLS REQUIRED: Adjustable Wrench. 7/16" Open End or Box Wrench. 9/16" Open End or Box Wrench. D (1) Pair of Pliers. E (1) Hammer F (1) Block of Wood. CONTENTS OF HARDWARE PACK: (See Figure 1) A (2) Hair Pin Cotters B (1) Rod Adjustment Link C (2) Cotter Pins 1/8" Dia. x 1.00" Long D (1) Spacer .50" I.D. x .62" O.D. x 1.62" Long E (2) Push Caps F (2) Shoulder Bolts (Rear Axles) G (2) Lock Washers 3/8" I.D. H (2) Hex Nuts 3/8-16 Thread I (2) Cable Ties J (4) Carriage Bolts 1/4-20 x 1.25" Long K (4) Lock Washers 1/4" I.D. L (4) Hex Nuts 1/4-20 Thread M (1) Hex Bolt 5/16-18 x 1.75" Long N (1) Compression Spring 0 (1) Flat Washer P (1) Hex Center Lock Nut 5/16-18 Thread Q (2) Hex Bolts 1/4-20 x 1.25" Long R (4) Hex Center Lock Nuts 1/4-20 Thread S (2) Hex Bolts 1/4-20 x 1.00" Long T (3) Grips U (1) Self-Tapping Screw 1. Remove the edger and all parts from the carton. 2. Make certain that all loose parts and literature are removed from carton before carton is discarded. Line up holes in lower handle with holes in frame. Secure rear wheels (larger) and lower handle to frame with shoulder bolts (F), lock washers (G) and hex nuts (H). See figure 2. 3. Using a hammer, tap one push cap (E) onto the end of the front axle which has a hole closer to it. See figure 3. 4 HOLES IN AXLE FRONT AXLE ¿a HAIR PIN COTTERS (A) FIGURE 4 HAIR PIN FIGURE 5 4. Starting on the right side of the edger, place the axle through the support arm on the frame. Then place axle through one wheel so the hub of the wheel is to the outside of the unit. Next place axle through spacer (D), the other wheel (hub to the outside of the unit) and through second support arm. See figure 4. Secure with push cap (E) by tapping it on with a hammer. See figure 5. It is necessary to hold a block of wood or a second hammer against the push cap on the other side of the axle. 5. Secure the front wheels and axle in position using two hairpin cotters (A). See figure 5. 6. 7. Slip the three handle grips (T) on the upper handles and the engagement handle. They will slip on more easily if you first soak them in warm, soapy water. Assemble the two upper handles to the lower handle with four carriage bolts (J), lock washers (K) and hex nuts (L). Tighten only finger tight at this time. See figure 6. FIGURE 6 5 I FIGURE 7 HEX LOCK NUT (R) FIGURE 8 8. Assemble the throttle control to the handle panel as follows. A. Hold the throttle control assembly beneath the handle panel. Turn the control sideways and insert the lever up through the wide portion of the slot on the handle panel. See figure 7A. B. After the end of the lever is through the slot, turn and then tip the control forward as shown in figure 7B to slide it through the slot. NOTE The lever must be all the way to the back of the contro...
Ce manuel est également adapté pour les modèles :Tondeuse à gazon - 24604C (1.37 mb)