Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
Specifications Construction Materials Tank, Sprayer Nozzle, Handle and Tires: Polyethylene. Extension Handle: ABS Battery Type AA 1.5 VOLT (QTY - 4 included) Tank Capacity 2 - Gallons Adjustable Nozzle Straight and Mist Switch Switch includes Safety Lock Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Cleaning Read the entire Important Safeguards section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Always rinse the Tank (3), Fluid Pickup (11), Misting Nozzle (13) and Power Sprayer Gun (12) completely with cold clean water at least twice before initial use, between different chemicals when finished. Dry with a soft cloth. Wipe with a soft clean cloth or sponge. Assembly Read the entire Important Safeguards section at the beginning of this manual including all text under subheadings therein before set up or use of this product.. Note: Layout all parts making and inventory according to Parts List and Parts Diagram on page 10 of this manual. Turn Collar (2) counterclockwise to loosen. Figure 14 1 2 34Insert the Extension Handle (1) into the Collar (2). Tighten the Collar (2) with clockwise motion until it is snug and the Stop-Ring (4) is located just above it. See Figure 1. 515 7 8Figure 2Slide Holster (5) onto Extension Handle (1). The Holster (5) must face the front and be on the right side of the Extension Handle (1) viewed from behind the sprayer. Fasten Screw (7) and Hex-Nuts (8) securely with screwdriver (not included). See Figure 2. Figure 366 87Slide the Black Handle (6) onto the Extension Handle (1) until the holes in the Black Handle (6) align with the holes in Extension Handle (1). Insert two Screws (7) in front holes and use the remaining two Hex-Nuts (8) to secure the Black Handle (6) to the Extension Handle (1). See Figure 3. Insert four AA Batteries (included) into the Battery Compartment located in the base of the Power Sprayer Gun (12). Snap the Wand Clip (9) onto the Extension Pole (1) above the Holster (5). Screw the Universal Cap (10) holding the Pickup Tube (11) onto the Tank (3). The Motorized Power Sprayer may be used with either the Power Sprayer Gun by itself (12), or by attaching the Misting Tube (13) to the end of the Power Sprayer Gun (12) when only a light mist is needed. Operation Read the entire Important Safeguards section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Clean the Motorized Power Sprayer before each use as explained in the “Cleaning” section on page 5 of this manual. Fill the Tank (3) to full capacity by removing the Fill Cap (14) and carefully pouring the liquid you will be using into the opening. Be sure to wipe off any spilled liquid from the exterior of the Tank (3). Note: The Fill Cap (14) may be used as a measuring cup. Calibrations are embossed into the side. Use chemicals only at strengths recommended by manufacturers’ label directions. Replace the Fill Cap (14). Point the Power Spray Gun (12) toward the ground and squeeze the trigger a few times to prime. Your Motorized Caddy Sprayer is now ready to use. Grab the handle and move the Caddy Sprayer into position. Squeeze the Trigger on the Power Spray Gun (12) and Spray with back and forth, or up and down motion keeping the Power Sprayer Gun (12), and/or the Misting Nozzle (13) approximately 12 inches from what you intend to cover with the product you are using. CAUTION: Do not spray against the wind. When you are finished, or if you intend to switch chemicals, always clean according to directions in “Cleaning” section on page 5 of this manual, and following directions recommended by the manufacturer of the chemical you are using for your project. INSPECTION and MAINTENANCE BEFORE EACH USE, inspect the general condition of this Motorized Caddy Sprayer. Check for loose screws, misalignment or binding of moving parts (including wheels), cracked or broken parts, and any other condition that may affect its safe operation. Troubleshooting Problem Possible Causes Probable Solutions Product will not spray from either Power Spray Gun or Misting Nozzle. Weak or dead Batteries. Fluid Tube or Nozzle(s) clogged. Fluid level in Tank too low. Check Batteries, replace if necessary with new. Check Fluid Tube and Nozzle(s) for blockage and flush with cold, clean water if needed. Check fluid level in Tank and fill to proper capacity. PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the produc...