Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
(See Figure 13) NOTE: Torque of spark plug is 18-22 foot-pounds (25-30 Nm) 8. Reattach spark plug wire to spark plug. Questions? Call Toll Free at 1-800-737-2112 14 Copyright © 2009 MAT Engine Technologies, LLC Maintenance (Continued) • Save all instructions H How to Prepare for Storage A WARNING Never store the edger indoors with fuel in the fuel tank. Never store in an enclosed, poorly ventilated area where fumes could reach an open flame, a spark or a pilot light as on a furnace, water heater or clothes dryer. Allow engine to cool before storing unit. A WARNING Do not remove gasoline while inside a building, near a fire, or while you smoke. Gasoline fumes can cause an explosion or a fire. NOTE: A yearly checkup or tune-up at an authorized service center will make sure that the edger will provide maximum performance for the next season. When the edger is put in storage for thirty days or more, the following steps should be followed to make sure the edger is in good condition the next season. 1. Let the engine run until it is out of gasoline. 2. Change the oil by following instructions under “How to Change the Oil.” 3. Remove the spark plug from the cylinder. Pour one ounce of oil into the cylinder. Slowly pull the recoil-start grip so that the oil will protect the cylinder. Install a new spark plug in the cylinder. Pull starter handle slowly a few times to distribute oil. Pull recoil slowly until resistance is felt. This will close the cylinder valves. A WARNING DO NOT attach spark plug wire to spark plug when storing unit. 4. Clean edger. Remove all dirt, leaves, debris, grease, etc. from the edger - including cylinder cooling fans, recoil starter cover holes, under fuel tank, and under muffler. 5. Check the edger for worn or damaged parts. Have damaged parts replaced if necessary. 6. Tighten any loose hardware. 7. Apply lubrication as directed in Maintenance section. 8. Put the unit in a building that has good ventilation. 9. Cover the edger with a breathing material. Questions? Call Toll Free at 1-800-737-2112 15 Copyright © 2009 MAT Engine Technologies, LLC Troubleshooting • Save all instructions PROBLEM POSSIBLE CAUSE(S) SOLUTION(S) Engine difficult to start 1. Out of fuel 2. Start lever is not compressed 3. Choke in “Run / Warm Start” position 4. Spark plug wire disconnected 5. Fouled spark plug 6. Dirty Carburetor 7. Clogged air filter 8. Clogged fuel filter 9. Contaminated Fuel 1. Add fresh fuel 2. Pull start lever against handle 3. Rotate Choke lever to “Choke / Cold Start” position 4. Attach spark plug wire to spark plug 5. Remove spark plug. Inspect. Replace if necessary 6. Take unit to an authorized service center for Carburetor cleaning 7. Remove and clean air filter 8. Remove fuel filter. Inspect. Replace if necessary 9. Drain fuel tank. Clean fuel tank. Fill with fresh fuel Engine Problems Engine smokes excessively Engine runs very “rough” Engine runs erratically Engine cannot maintain full speed 1. No Engine Oil 2. Engine oil not at proper level 3. Fouled spark plug 4. Clogged air filter 5. Clogged fuel filter 6. Contaminated Fuel 7. Carburetor out of adjustment 8. Choke in “Choke / Cold Start” position 1. Add engine oil 2. Check engine oil. Add or drain engine oil if necessary 3. Remove spark plug. Inspect. Replace if necessary 4. Remove and clean air filter 5. Remove fuel filter. Inspect. Replace if necessary 6. Drain fuel tank. Clean fuel tank. Fill with fresh fuel 7. Take unit to an authorized service center for Carburetor adjustment 8. Rotate Choke to “Run / Warm Start” position Excessive vibration / noise 1. Loose parts 2. Engine problems (above) 1. Tighten all fasteners 2. Refer to engine solutions (above) Blade will not rotate 1. Debris interfering with blade 2. Blade loose 3. Belt Loose 1. Remove debris from around blade 2. Tighten blade nuts 3. Replace Belt Engine will not stop Flameout wire terminals disconnected Connect handle and engine flameout wire terminals Blade will not cut properly Damaged or worn blade Replace blade Frequent engine stalling 1. Excessive edging speed / depth 2. Engine problems (above) 1. Edge at a moderate pace. Make multiple passes. 2. Refer to engine solutions (above) Questions? Call Toll Free at 1-800-737-2112 16 Copyright © 2009 MAT Engine Technologies, LLC Technical Service You may have further questions about assembling, operating, or maintaining this EDGER. If so, you can contact our Technical Service Department at 1-800-737-2112 (English only). You may also write to: METL Corporate Office - CORRESPONDENCE ONLY ATTN: Technical Service - METL 6700 Wildlife Way Long Grove, IL 60047 If you need assistance or have any questions, CALL TOLL FREE: 1-800-737-2112. When contacting the Technical Service Department, have ready: • Your Name • Model Number of Product • Your Address • Date of Purchase (include copy of receipt for written requests) • Your Phone Number Warranty • Save all instructions A Power...