Évaluations - 3, GPA: 4.7 ( )

Fabricant : Ariens Taille : 826.18 kb Nom Fichier : Langue d'enseignement:

Briggs & Stratton Intek Engines: Place handlebar into handlebar service position and tip the machine to the left, opposite the discharge opening. Kawasaki: Place handlebar in service position and tip unit to right. IMPORTANT: If engine becomes "flooded" due to tipping, clean air cleaner and remove spark plug, put one teaspoon of oil in cylinder, turn engine over a few times and reinstall spark plug. 4.3 FILLING THE FUEL TANK WARNING: EXPLOSIVE VAPORS and its FLAMMABLE FUEL can result in death or serious injury. Handle fuel with care. ALWAYS use an approved fuel container. No Smoking! No lighted Materials! No Open Flame! Allow engine to cool before maintenance. Gasoline is highly flammable and must be handled with care. Allow engine to cool several minutes before removing fuel tank cap. Never fill tank when engine is running or is hot from operation. DO NOT allow open flame, matches, or smoking in area. DO NOT overfill. Allow about 1/4" of tank space for fuel expansion. Wipe up any spills and allow vapors to dissipate before starting engine. Use approved gasoline container. To add fuel to fuel tank: 1. Put unit in open or well-ventilated area. 2. Stop engine and allow to cool. 3. Clean fuel cap and surrounding area to prevent dust, dirt and debris from entering fuel tank. 4. Remove cap. IMPORTANT: DO NOT use gasohol or gasoline containing alcohol because alcohol will cause internal parts to deteriorate. See Engine Manual for correct type and grade of fuel. 5. Fill fuel tank. (See Specifications for tank capacity.) 6. Replace fuel cap and tighten. 7. ALWAYS clean up any spilled fuel. 4.4 GENERAL LUBRICATION Swivel Lubrication (swivel units) See Figure 4. Apply Sten Mix Hi-Temp Grease or equivalent to the lube fittings. Order P/N: 00036800 - 3 pack of 3 oz. cartridges. When using Sten Mix Grease for the first time, all components should be thoroughly cleaned prior to lubricating. Commercial Models Grease fittings on rear axle housing every 25 hours. 4 - 22 2 2 Grease Fitting 2. Swivel Lock Hole Figure 4 OM0210 4.5 CHECK MOWER BLADE See Figures 5 and 6. Regularly check mower blades for wear and that lock washer is fully compressed by cap screw (requires 25-30 ft-lbs (33-40 Nm) of torque on cap screw). When blade needs sharpening: 1. Block blade to prevent rotation. 2. Remove cap screw, lock washer and blade from shaft. 3. Sharpen both ends of blade at original angle (25o), removing equal amounts of material from each end to maintain proper blade balance. New blades are balanced to within 1.3 in. oz. at factory. DO NOT grind around corner at tip of blade. If cutting edge of blade cannot be sharpened in a straight line to within 1/8 of an inch of its end, replace blade with Ariens replacement blade only. 4. Install blade, lock washer and tighten cap screw 25-30 ft-lbs (33-40 Nm) until lock washer is fully compressed. IMPORTANT: If mower is used under sandy soil conditions, replace blades when air lifts become eroded. 4.6 CHECK DRIVE BELT Figure 5 1. Cutting Edge 2. Square Corner 3. Air Lift Erosion 4. Air Lift 5. Reverse Lift OM0240 OM0230 1 2 3 4 5 12 3 4 1 4 1. Blade 3. Drive Belt 2 3 2. Cap Screw, Lock 4. Idler Washer & Flat Washer Figure 6 OM0250 Check drive belt for wear or damage. Replace belt if worn or damaged. 4.7 CHECK ENGINE/BLADE CONTROL The engine/blade control must stop the engine and blade within 3 seconds after the bail is released. If the engine or blade continues to run, adjust or repair control immediately. Engine control must stop engine ignition, at 3/4" to 1-1/4" from handlebar as control is released. 4 - 23 To check (Figure 7): To check (Figure 7): . Start engine and slowly release control until engine stops firing. 2. Measure distance between handlebar and control at the point that engine stopped firing. 3. Turn cable nuts at handlebar mount clockwise if measurement is more than 1-1/4" or counterclockwise if measurement is less than 3/4". 4. Turn nuts against mount to lock in position. 2 1 4 3 1. Engine Control 3. Cable Nuts 2. Handlebar 4. Mount Figure 7 OM0280 1-1/8" to 1-5/16" 1 2 3 1. Cable Nuts 2. Bracket 3. Spring Figure 8 There must not be slack in cable. To check, rotate blade in it’s cutting direction (this draws control rod fully in). To eliminate slack in cable, turn nuts on cable at handlebar clockwise. 1 2 3 4 5 S Hook on Some Models 1. Cable Nuts 4. Spring or "S" Hook 2. Bracket 5. Control Rod 3. Spring Figure 9 4.8 CHECK GRASS BAG Check bag for wear or damage. Keep bag clean and dry. Replace only with Ariens original equipment replacement bag. 4.9 CHECK DRIVE CONTROL Check operation of drive control. The drive must disengage completely when the bail handle is released. Adjust bail travel if necessary. See Figure 10. When the wheel drive control is squeezed toward the handlebar, the extension spring, located at the bottom end of the traction cable, must start to extend when the control is between 1-1/2" and 2" (3.8 and 5 cm) away from the handlebar. To check: 1. Squeeze the w...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :