|
Facilité d'utilisation
Install Spacers 1. Install the rear spacers (C, Figure 3). Secure with two 1/2-13 x 2-1/2 capscrews (E), washers (D), spacers (C), and 1/2-13 nylock nuts (A) per side. A C D D B Figure 3. Install Rear Spacers A. Nylock Nuts, 1/2-13 C. Spacers B. 1/2-13 x 2-1/2 Capscrew D. 1/2” Washers 4 Initial Assembly & Installation Figure 4. Upright Identification Use this upright with Broadmoor / 1600 / 2600 / LT Series Use this upright with Prestige / 1800 / 2800 / YT & Conquest / 1700 / 2700 / GT Series Figure 5. Assemble Catcher Frame A. Upright Support C. Horizontal Support B. 3/8-16 x 7/8 Capscrew D. 3/8-16 Whizlock Nut A B C D Prestige Mounting Holes Conquest & Broadmoor Mounting Holes A B D C A Figure 6. Assemble Catcher Frame (Prestige Shown) A. 3/8-16 Nut & Lockwasher C. 3/8-16 x 1 Capscrews B. Upright Support Assy. D. Lower Support A A DB B C C CATCHER ASSEMBLY - ALL MODELS Assemble Supports and Hitch 1. Refer to Figure 4 to select the proper upright support for your application. 2. Bolt the upright support (A, Figure 5) to the horizontal support (C). Secure with 3/8-16 x 7/8 capscrews (B) and 3/8-16 whizlock nuts (D). 3. Bolt the lower support plate (D, Figure 6) to the upright support (B) using two 3/8-16 x 1 capscrews (C), lockwashers, and 3/8-16 nuts (A). 4. Install the hitch side plates (B, Figure 7) and secure with four 3/8-16 x 1-1/4 capscrews (C), lockwashers, and 3/8-16 nuts (A). Figure 7. Assemble Catcher Frame (Prestige Shown) A. 3/8-16 Nuts & C. 3/8-16 x 1-1/4 Capscrews Lockwashers D. Support Assembly B. Side Plates 5 Initial Assembly & Installation Figure 8. Install Catcher (Prestige Shown) A. #10-32 Nut F. Bags B. Handle G. Hair Pin Clip C. #10-32 x 1/2 Screw H. Catcher Hitch D. Cover I. Spacers E. Hinge Pin I AB C D E F H G Install Cover and Bags 1. Mount the catcher hitch (H, Figure 8) on the frame spacers (I). 2. Hang the bags (F) on the horizontal support. 3. Install the handle (B) inside the cover. Secure with two #10-32 x 1/2” screws (C) and #10-32 nuts (A). 4. Rest the cover assembly (D) on the bags (F). 5. Install the two hinge pins (E) and secure with hair pin clips (G). 6. Open the cover and fasten cable (A, Figure 9) to support (B). The looped cable end fits over washer (C). A B C Figure 9. Install Cable A. Cable C. Washer B. Support F E A B C D Figure 10. Install Tubes A.Flange Nut D. Lower Tube B.Clip E. #10-32 Nut & Washer C.#10-32 x 1/2 F. Upper Tube Screw & Washer Assemble & Install Tubes NOTE: Install turbo blower at this time. 1. Locate the lower tube (D, Figure 10) and upper tube (F). 2. Assemble the upper and lower tubes using two #1032 x 1/2 screws (C), washers, and #10-32 nuts (E). 3. Insert the tube assembly into the catcher. 4. Connect the lower tube (D) to the turbo. Lock the clip (B) on the flange nut (A). 6 Normal Removal & Installation Figure 11. Normal Removal & Installation (Prestige Shown) A. Tubes B. Hair Pin Clip C. Frame Spacers D. Bags E. Clevis Pin F. Cover G. Clip E F D B C A G Normal Removal & Installation Figure 11. Normal Removal & Installation (Prestige Shown) A. Tubes B. Hair Pin Clip C. Frame Spacers D. Bags E. Clevis Pin F. Cover G. Clip E F D B C A G WARNING OPERATION WITHOUT TURBO & CATCHER For operation without turbo, the mower deflector MUST be properly installed in the down position and retained by the spring latch (see turbo operator’s manual). NORMAL REMOVAL & INSTALLATION Removal 1. Disconnect the tubes (A, Figure 11) from the turbo and remove them from the catcher. 2. Remove the hair pin clip (B) and clevis pin (E) securing the cover (F). Disconnect the cable (see Figure 8). Remove the cover (F). 3. Remove and empty the bags (D). 4. Remove the catcher frame from the frame spacers Installation 1. Mount the catcher frame on the frame spacers (C, Figure 11). 2. Install the bags (D). 3. Install the cover (F). Secure with the clevis pins (E) and hair pin clips (B). 4. Connect the cover cable (Figure 9). 5. Insert the tubes (A, Figure 11) into the catcher and connect to the turbo. Be sure the clip (G) is secured over the top of the turbo flange nut. (C). 7 Installation with a Tiller A B C DA B C D E F G H I A B C DA B C D E F G H I Figure 12. Initial Setup (Prestige Shown) Figure 13. Installation (Prestige Shown) A. Nuts, 5/16-18 G. Carriage Bolts, A. Tiller Hitch C. Hair Pin Clip B. Lockwashers, 5/16 3/8-16 x 3/4 B. Clevis Pin D. Support Assembly C. Plate H. Nuts & Lockwashers, D. Spacers 3/8 E. Lower Support I. Upright Support F. Carriage Bolts, 5/16-18 x 1-1/4 INSTALLATION WITH A TILLER Initial Setup Note: Use the short upright bracket (refer to Figure 4). 1. Assemble the lower support (E, Figure 12), spacers (D), and plate (C) as shown). 2. Bolt the lower plate assembly (E) to the upright support (I) using four 3/8-16 x 3/4 carriage bolts (G), lockwashers, and 3/8-16 nuts (H). Installation & Removal 1. Rest the support assembly (D, Figure 13) on the tiller hitch (A) cross-bar. 2. Secure the catcher to the tiller hitch using two clevis pins (B) an...
Ce manuel est également adapté pour les modèles :Tondeuse à gazon - 1694153 (621.49 kb)
Tondeuse à gazon - 1723846 (621.49 kb)