Évaluations - 3, GPA: 3.7 ( )

Fabricant : Poulan Taille : 853.5 kb Nom Fichier : Langue d'enseignement:

• Turn ignition key "OFF" and remove key. • Make sure the blade and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. 6 7 SUPPORT POST (See Fig. 3) Use Hardware - - GROUP "B" 1. Rotate cover assembly onto its side as shown. 2. Secure support tubes to cover assembly using short hex bolts, long hex bolts, and locknuts as shown. Tighten all hardware securely. 02086 02357 1 REAR MOUNTING BRACKET and SUPPORT PLATE (See Figs. 1A & 1B) Use Hardware - - GROUP "A" 1. Install support plate to inside of drawbar as shown, using two (2) 7/16-14 x 3/4 hex bolts and the two threaded upper holes in the plate. Do not tighten at this time. NOTE: Be sure to align the four (4) lower threaded holes of the support plate with the holes in the drawbar. 2. Assemble the mounting bracket as shown to the out side of the drawbar using four (4) 7/16-14 x 3/4 hex bolts and the four (4) lower threaded holes of the support plate. Tighten all hard ware securely. Fig. 1B COVER SEAL (See Fig. 2) No hardware required 1. Align mark on seal with mark at cover opening. 2. Work seal into opening so cover sits between fl anges of seal. 2 3 ALIGNMENT MARKS COVER SEAL Fig. 2 DRAWBAR HEX BOLTS THREADED UPPER HOLES SUPPORT PLATE Fig. 1A HEX BOLTS SUPPORT PLATE DRAWBAR THREADED LOWER HOLES MOUNTING BRACKET 02356 LOCKNUTS LOCKNUTS SUPPORT POSTS LONG HEX BOLTS SHORT HEX BOLTS COVER ASSEMBLY Fig. 3 8 02360 MOUNTING TO TRACTOR (See Fig. 4) Use Hardware - - GROUP "C" NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting assembly to tractor. 1. Raise seat on tractor to allow assembly to be mounted. 2. With cover closed, lift assembly and place support posts into mount ing bracket. Allow assembly to rest on bottom of mounting bracket. 3. Line up holes in mounting bracket with holes in support posts and insert support post clevis pins. Secure with re tain er springs. 4. Install the four (4) tubing end caps onto container support. Tap each end cap onto container support tubes to seat securely. 4 COVER AS SEM BLY Fig. 4 END CAP SUPPORT POST MOUNTING BRACKET SUPPORT POST CLEVIS PINS RE TAIN ER SPRINGS DRAWBAR CONTAINER ASSEMBLY (See Fig. 5) No hardware required 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET. 4. Repeat for other containers. PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF 02089 CONTAINER BOTTOM HALF CONTAINER TOP HALF ASSEMBLY CHECK: Squeeze sides of lower half of contain er and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. LOCKING TAB WARNING Donotoperatemowerunlesscontainerisprope rlyissubjecttowearanddetierioration.Checkbagfrequ ently.Replacewhencrackedor damaged.Useonlyarecomme ndedreplacementcontainer. 02097 FIG. 5 5 02739 CONTAINER BOTTOM HALF CONTAINER TOP HALF 9 WARNING Donotoperatemowerunlesscontainerisproperlyisnstalled.Containeris subjecttowearand detierioration.Check bagfrequently. Replacewhen crackedor damaged.Use onlyarecommended replacementcontainer. WARNING Donotoperate mowerunlesscontainer isproperlyisnstalled.Containeris subjecttowearanddetierioration.Checkbagfrequently.Replacewhen crackedordamaged.Useonlyarecommendedreplacementcontainer. 02083 CONTAINER MOUNTING (See Fig. 6) No hardware required 1. Install one container to left side fi rst with warning to outside of unit. Install another container to center position and one in right position. NOTE: Right con tain er should always over lap left con tain er at center supports. 2. Close cover and lock latch handles over center sup port tubes. 6 Fig. 6 COVER LATCH HANDLES CONTAINER WARNING CONTAINER HANDLE CONTAINER WARNING CENTER SUPPORT TUBES LOWER CHUTE (See Fig. 7A & 7B) Use Hardware - - GROUP "D" 1. Press weld nut into rubber latch and install two latch hook as sem blies to lower chute using screw, washer, and lock washer as shown. 2. Tighten hard ware securely. 3. Raise and hold defl ector shield in upright position. 4. Place rear of chute over rear of mower deck opening. Push chute down and forward to guide extended edge of chute between discharge guard and mower deck. 5. Hook front latch into tab hole on front of mower deck. 6. Hook rear latch into fl ange hole on back of mower deck. 7 CAUTION: Do not remove discharge guard from mower. Raise and hold guard when at tach ing lower chute and allow it to rest on chute while in op er a tion. Fig. 7A 02094 SCREW WELD NUT LATCH WASHER LOCK WASHER REAR LATCH FRONT LATCH DE FLEC TOR SHIELD Fig. 7B 10 02101 LEVEL MOWER DECK No hardware required • Be sure deck is properly leveled for best mower per for mance. See your tractors owner'...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :