Évaluations - 2, GPA: 5
(
)
)
|
Facilité d'utilisation
ASSEMBLY _WARNING: If received as sembled, repeat all steps to ensure _/aOUrunit is properly assembled and all steners are secure. • A hex wrench (provided) is required for assembly, HANDLEBAR ASSEMBLY DANGER: RISK OF CUT, To avoid serious injury, the barrier portion of the handlebar must be installed as shown on the upper shaft of the pew erheed to provide a barrier between operator and the spinning blade. Attach handlebar mounting bracket above arrow on safety warning decal on the upper shaft (pewerhead end of unit). Ensure handlebar is positioned on mounting bracket at the end of the arrow on the handlebar decal, NOTE: Two mounting brackets are in cluded with this attachment. Both brack ets are provided to adapt this attachment for use with powerheads that have either a 1" (2.5 cm) diameter or a 7/8" (2.2 cm) diameter upper shaft. The correct bracket must be used to ensure that the handlebar is mounted securely to the upper shaft before use, Handlebar _. _ _-_ Screw _ Bracket Cover Mounting _.._ Bracket ,' ! 1. Place the mounting bracket over the upper shaft above the arrow on the safety label. Be sure to use the correct mounting bracket for either the 1" (2.5 cm) or 7/8" (2.2 cm) diameter upper shaft. 2. Position one of the bracket covers under the upper shaft and align the mounting bracket and the bracket cover screw holes. Insert two screws into the screw holes. 3. Secure the mounting bracket by tightening the screws with the hex wrench. 4. Locate the decal on the handlebar. This decal includes an arrow. Position the handlebar with the mounting bracket at the end of the arrow. 5. Position the second bracket cover over the handlebar. mounting bracket cover screw holes. sure the handlebar the arrow. 6. Insert two screws Align the and the bracket Again make is at the end of and hand tighten only. Be sure the handlebar is installed correctly; then, tighten each screw securely with the hex wrench. 6 KNOW YOUR EDGER ATTACHMENT READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR EDGER ATTACHMENT Compare the illustrations with your attachment to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. Depth Adjustment Knob Gearbox BLADE TheBLADEisdesignedtocutsod. OPERATING THE COUPLER Your powerhead is equipped with a coupler which enables optional attachments to be installed. The optional attachments are: Cultivator ............ C944.511580 Blower .............. C944,511601 _WARNING: Always disconnect powerhead spark plug (or disconnect powerhead from power source) before removing or installing attachments. REMOVING ATTACHMENT CAUTION: When removing or instal ling attachments, place the power- head and attachment on a flat surface for stability. 1. Loosen the coupler by turning the knob counterclockwise. Hanger Blade Shield .Wheel Edger Blade DEPTH ADJUSTMENT KNOB The DEPTH ADJUSTMENT KNOB is used to adjust the wheel for blade cutting depth. Upper Shaft Coupler Lower Attachment TIGHTEN Knob 2. Press and hold the locking/release button. Locking/Release Button Upper Shaft Lower Attachment 3. While securely holding the upper shaft, pull the attachment straight out of the coupler. 7 INSTALLING ATTACHMENT 1. Remove the shaft cap from the attachment (if present) and discard. 2. Position locking/release button of attachment into guide recess of upper shaft coupler. Coupler Primary Hole Upper Locking/ Attachment Shaft Release Button 3. Push the attachment into the coupler until the locking/release button snaps into the primary hole. 4. Before using the unit, tighten the knob securely by turning clockwise. INSTALLING ATTACHMENT HANGER An attachment hanger is provided for storage when attachment is not in use. To install hanger on attachment: 1. Remove the shaft cap from the attachment (if present) and discard. 2. Press and hold the locking/release button. 3. Push hanger onto the attachment until the locking/release button snaps into the hole. OPERATING POSITION ALWAYS WEAR: Eye Protection Heavy Shoes When operating unit, stand as shown and check for the following: • Wear eye protection and heavy clothing. • Keep right arm slightly bent with right hand holding the trigger handle of powerheed. • Keep left arm extended with left hand holding the handlebar. • Keep unit below waist level. • Adjust edger wheel for proper cut depth. ,_ WARNING: Never attempt fo adjust the edger wheel when the unit is in operation. Always stop the powerhead, wait until the blade stops turning, and disconnect the spark plug (or disconnect powerhead from power source) before making adjustments. EDGING As you become familiar with use of your edger attachment, you will be able to determine your own operating pace. Conditions such as depth of cut and material being cut will regulate the speed and time required for your edging job. • Allow the engine to warm up before you begin edging. • Increase the engine speed before placing the blade in the cut. For best results, ru...
Ce manuel est également adapté pour les modèles :Tondeuse à gazon - C944.511572 (884.17 kb)