Évaluations - 4, GPA: 3.5
(
)
)
|
Facilité d'utilisation
Tighten securely. BAGGER KIT INSTALLATION STEP 11: Install bumper mount standoffs onto rear bumper of machine, utilizing existing hardware on machine. NOTE: Invert hardware when installing standoffs, installing bolts out through bumper with nuts facing out. NOTE: When installing standoffs, be sure that the bumper mount plate mounting holes along the back bar of the standoffs are located towards the right side of the machine. Refer to the Parts List section of the manual. STEP 12: Install bumper mount plate onto standoffs with four 5/16-18 x 3/4 hex cap screws, securing with four 5/16-18 flange lock nuts. Tighten securely. Also, install muffler deflector (see inset) onto muffler, making sure deflector directs exhaust off to the side of the mower. Fasten with clamp. IMPORTANT: FAILURE TO INSTALL MUFFLER DEFLECTOR MAY RESULT IN A FIRE. 7 INSERT PIN INTO ROD STEP 13: Hook bottom of bagger frame onto pins in bottom of bumper mount plate. Then slide locking rod through aligned holes in bagger flame and bumper mount plate, securing with bridge pin. HOOK BAGGER FRAME ONTO BUMPER MOUNT PLATE PINS CROSS ASSEMBLY STEP 14: Install cross assembly onto bagger frame with four 3/8-16 x 3/4 bolts and hex flange lock nuts, tightening securely. Insert bolts back through bagger frame and into cross assembly. STEP 15: Insert two 5/16-18 x 3/4 bolts through reinforcement plate (not shown; refer to Parts List -Catcher Mount Group), then through holes in bagger frame. Install cover latch arm onto bolts and secure with hex flange lock nuts, tightening securely. NOTE: Use the leftmost set of holes in the bagger frame when installing arm. STEP 16: Lay cover assembly on cross assembly. Align hinges on cross assembly with hinges on cover, and install one round head pin through each set of hinge holes, securing with a hair pin. ROUNDHEAD PIN I STEP 17: Slip looped end of cover support cord onto threaded stud on hose adapter assembly. Secure end of cord with one 3/16" flat washer and 10-32 nyloc nut (not shown). Run nut all the way in on thread, but leave cord loose enough to swivel. 8 STEP18: Installbagsontocrossassemblyby hookingslotin baghangerontotabsin channel assembly. STEP19:Closecoverandlockin placebyhookinglockknobintoslotin coverlatcharm. STEP20:Sliponehoseclampontoeachendof hose(usetheclampwiththe blackquick-release knobattheblowerend),andinstallhosebetween blowerandbagger.Makesuretofit hosesfirmly ontoadapters.Tightenclampssecurely. INTRODUCTION Follow operation and maintenance instructions in the Operator's Manual provided with the Snapper CZT/HZT. GRASS CATCHER OPERATION 1. Select desired cutting height. Choose a setting that will not attempt to cut off too much at once, overloading the machine. 2. After starting engine and allowing a brief warm up period, move engine speed control to highest setting. 3. Drive machine to cutting area. Engage blades. 4. Select a slow forward ground speed until familiar with conditions. Do not select a speed that is too fast, causing the machine to become overloaded. 5. The weight of the grass catcher and contents will affect the stability and handling of the machine. Avoid sudden starts and sharp turns. Reduce speed on slopes, and DO NOT operate machine on slopes exceeding 10 degrees (18% grade). Operate machine up and down slopes. DO NOT operate machine across the face of slopes. Turn blades off when traveling up slope. 6. Empty grass catcher bags often to minimize effect on stability and handling. Over filling the catcher bags will reduce performance and cause clogging of the hose, blower and deck. 7. Do not operate the machine with the Grass Catcher cover open. The entire Grass Catcher must be installed, the cover closed and latched properly before operating. EMPTYING GRASS CATCHER 1. Empty Grass Catcher bags often to avoid overfilling. Overfilling reduces performance and causes clogging of hose, blower and deck. 2. Turn blades off. Drive machine to location the clippings are to be dumped. DO NOT operate blades in reverse. If you must back machine to dump clippings in desired location, LOOK and SEE behind and down for children, pets and hazards before and while backing. 3. Stop motion of machine by returning Motion Control(s) to Neutral (N). Set Park Brake. Stop engine. 4. Unlatch cover and lift. Remove bags and dump debris in desired location. 5. After dumping, to maintain peak performance, check the catcher screen located on the inside of the Cover Assembly to make sure it is clean and free of any build up. Clean as required with brush or broom. 6. Close catcher cover and latch. 7. Re-start engine and drive machine to cutting area. Set engine speed to highest setting, engage blades and resume operation. WARNING DO NOT attempt to remove any clogs from deck, blow er, or hose with engine or blade running. STOP engine. STOP blades. Set brake. Remove key. Make sure blades and all rotating components have come to a complete stop before removing any catcher or unclog ging any catcher component...
Ce manuel est également adapté pour les modèles :Tondeuse à gazon - P/N 7078273 (3.21 mb)