Évaluations - , GPA: ( )

Instructions Poulan, Modèle 532140600

Fabricant : Poulan
Taille : 727.42 kb
Nom Fichier : NOUS2003_532140600.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

To protect grass catcher cover (1) Upper Chute (1) Cover Seal during assembly place cover upsidedown on overturned carton. (1) Lower Chute (1) Bag of Parts • Check carton contents against list. Be sure all parts (1) Support Post (1) Owner's Manual are there. (2) Wheel Weights NOTE: For ease of assembly, aside of your work area, lay out all hardware in the following groups. Each step of the assembly instructions will identify the group needed for that step. GROUP "A" GROUP "B" ASSEMBLY LOCATION HARDWARE SHOWN ACTUAL SIZE BAG OF PARTS CONTENTS (4) Shoulder Bolt, Self-Tapping (3) Carriage Bolt 5/16 - 18 x 3/4 (3) Locknut 5/16-18 (2) Bolt 5/16 - 18 x 1 (2) Locknut 5/16-18 (2) Nut, Acorn 5/16-18 (1) Bracket Support Pin (1) Retainer Spring (3) Tubing End Caps LATCH HOOK ATTACHMENT TO MOWER DECK REAR MOUNTING BRACKET TO DRAW BAR GROUP "C" GROUP "D" SUPPORT POST TO CORNER SUPPORT SUPPORT POST TO MOUNTING BRACKET 4 BAG OF PARTS CONTENTS (continued) GROUP "F" GROUP "E" CHUTE LATCH ASSEMBLY to UPPER CHUTE (1) Screw #10 x 1-1/8 (2) Washer 3/16 x 3/4 x 16 Ga. (1) Nut, Acorn #10 (1) Spacer, Split #10 (1) Rubber Latch LOWER CHUTE ASSEMBLY TO MOWER DECK GROUP "G" CHUTE LATCH ASSEMBLY to LOWER CHUTE GROUP "H" (2) "U" Bolt (4 ) Locknut **ITEMS NOT SHOWN FULL SIZE** WHEEL WEIGHTS TO FRONT WHEELS (2) Nut, Weld #10 (2) Washer, Lock #10 (2) Washer 3/16 x 3/4 x 16 Ga. (2) Screw #10 x 5/8 (2) Latch Hook Assembly (1) Nut, Weld #10 (1) Washer, Lock #10 (1) Washer 3/16 x 3/4 x 16 Ga. (1) Screw #10 x 5/8 5 ASSEMBLY BEFORE YOU START TO ASSEMBLE THE GRASS CATCHER Some mower models may need minor modifications before you can mount the grass catcher to the unit. Look carefully at the mower deck on your unit and compare the deck mandrel to the illustrations below. If your mower deck mandrel looks like STYLE "A", your unit is ready - proceed with the grass catcher assembly. If your mower deck mandrel looks like STYLE "B", go to the PREPARATION section in this manual. DECK MANDREL DECK MANDREL STYLE "A" STYLE "B" PARTS IDENTIFICATION COVER WARNINGDonotoperatemowerunlesscontainerisproperlyissubjecttowearanddetierioration.Checkbagfrequently.Replacewhencrackedordamaged.Useonlyarecommendedreplacementcontainer. WARNINGDonotoperatemowerunlesscontainerisproperlyissubjecttowearanddetierioration.Checkbagfrequently.Replacewhencrackedordamaged.Useonlyarecommendedreplacementcontainer. 02084UPPER CHUTE CHUTE LATCH LOWER CHUTE ATTACHING STRAPSLOWER CHUTE CONTAINERS FULL BAG INDICATOR WHEEL WEIGHT U-BOLT GRASS CATCHER NOTE: When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you are seated on the tractor, in the operator's position. (1) 3/8" Wrench (1) Drive Ratchet (1) 1/2" Socket (1) 3" or longer Extension THESE ARE THE TOOLS YOU WILL NEED TO AS (1) 9/16" Socket (1) Short Handle SEMBLE YOUR GRASS CATCHER: Phillips Screwdriver CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR: • Depress clutch/brake pedal fully and set parking brake. • Place gearshift/motion control lever in neutral (N) position. • Place attachment clutch in "DISENGAGED" position. • Turn ignition key "OFF" and remove key. • Make sure the blade and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. 6 7 02462 1 HEX BOLT LOCKNUT ACORN NUT DISCHARGE GUARD LOCKNUT MOWER DECK BAFFLE (See Fig. 1) Use Hardware - - GROUP "A" 1. Raise your tractor mower deck to its highest position. 2. Install the hex bolts, locknuts and acorn nuts through mower deck housing as shown. 3. Tighten all hardware securely. ACORN NUT FIG. 1 2 REAR MOUNTING BRACKET (See Figs. 2A & 2B) NOTE: If your tractor already has four (4) shoulder bolts installed on the rear draw bar, simply hang the mounting bracket, lanced tabs towards bottom, on the bolts. Discard hardware group "B" and disregard the remaining Step 2 instructions. LANCED TABS TOWARD BOTTOM SHOULDER BOLTS FIG. 2A If your tractor does not have four (4) shoulder bolts installed on the drawbar, follow the instructions below. Use Hardware - - GROUP "B" 1. Using the four formed holes in the drawbar, install the four shoulder bolts as shown and tighten securely. 2. Hang the mounting bracket, lanced tabs towards bottom, on the bolts. 02461 SELF TAPPING SHOULDER BOLTS FIG. 2B LANCED TABS TOWARD BOTTOM HEX BOLT 02085 ALIGNMENT MARKS COVER SEAL FIG. 3 COVER SEAL (See Fig. 3) No hardware required 1. Align mark on seal with mark at cover opening. 2. Work seal into opening so cover sits between fl anges of seal. 3 02091 SUPPORT POST (See Fig. 4) Use Hardware - - GROUP "C" CAUTION: Container sup port is spring loaded and locked to the cover. Handle cover assembly carefully so as not to unlatch the cover from the container support. 1. Rotate cover assembly onto its side as shown. 2. Assemble support post to container support with the three (3) carriage bolts and locknuts. Tighten securely. 4 FIG. 4 LOCKNUTS CARRIAGE BOLTS SUPPORT POST 8 02096 FIG. 5 ...