POLY PRO DROP SPREADER OWNERS MANUAL Model No. 45-02881 ™ • Safety • Assembly • Operation • Maintenance • Parts CAUTION: Read Rules for Safe Operation and Instructions Carefully 175 LB. POLY PRO DROP SPREADER OWNERS MANUAL Model No. 45-02881 ™ the fastest way to purchase parts PRINTED IN U.S.A. FORM NO. 47717 (REV. 8/06) RULES FOR SAFE OPERATIONS Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all ti

Outside the tank, assemble the nylon washer, then the nylon nut onto the drain body. Tighten the nut securely enough to prevent leaking, being careful not to damage the plastic parts. Place the O-ring inside the nylon cap and screw the cap onto the end of the drain body. See figure 4. NYLON NUT O-RING NYLON CAP HOSE GASKET DRAIN BODY NYLON WASHER FIGURE 4 9. Assemble the boom mount bracket to the rear of the hitch tubes using two 5/16" x 2" hex bolts and 5/16" hex nuts. See figure 5. BOOM MOUNT

Spray Gun Assembly 7. Axle 8. Hitch Arms (2) 9. Hitch Brackets (2) 10. Wheels (2) 1. Lid 2. Tank 3. Return/Bypass Hose (may be assembled to tank) 4. Boom Assembly 5. Boom Mount Bracket 13610947528 ENGLISH SHOWN FULL SIZE OP204060801000NOT SHOWN FULL SIZEQRTUSNAHJKLBCDGFEIM HARDWARE PACKAGE - FULL SIZE KEY QTY. DESCRIPTION A 8 Hex Bolt, 5/16" x 2" B 2 Hex Bolt, 5/16" x 1-1/4" C 2 Carriage Bolt, 5/16" x 1-1/4" D 2 Screw, #10 x 3/8" E 4 SEMS Nut, 5/16" F 10 Nylock Nut, 5/16" G 2 Flat Washer, 5/16"

Modelo No. Modele No. 45-02941 (40") 45-02951 (48") TINE DE-THATCHER ADITAMENTO DE EXTRACCION DE PAJA DECHAUMEUSE CAUTION: Read Rules for Safe Operation and Instructions Carefully • Safety • Assembly • Operation • Maintenance • Parts PRECAUCION: Lea cuidadosamente los Procedimientos e Instrucciones para la Operacion Segura de la Maquina. • Seguridad • Montaje • Operacion • Mantenimiento • Piezas de Repuesto ATTENTION: Lire et suivre attentivement les instructions et consignes de securite de cett

3. Assemble four aerator knives on the outside of each single spool assembly. Rotate each knife to insert the locking tab into the spool plate, then align the square holes and secure with a 5/16" x 3/4" carriage bolt, 5/16" lock washer and 5/16" nylock nut. See figure 2. 4. Push split plastic bearings into each end of the spool tube. See figure 2. 5/16" x 3/4" CARRIAGE BOLT (F) 5/16" LOCKWASHER (N) 5/16" NYLOCK NUT (K) SPLITBEARING (W) SPLITBEARING (W) CAUTION: POINTS OF AERATOR KNIVES ARE SHARP

45-0299 48" PLUG AERATOR CAUTION: Read Rules for Safe Operation and Instructions Carefully Assembly Operation Maintenance Repair Parts thefastest way to purchase parts PRINTED IN USA FORM NO. 48309 (4/25/07) RULES FOR SAFE OPERATIONS Remember, any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. CAUTION: VEHICLE BRAKING AND STABILITY MAY BE AFFECTED WITH THE ADDITION OF AN ACCESSORY OR AN ATTACHMENT. BE AWARE OF CHANGING CON

PULLEY CLUTCH LEVER PLUNGER REAR DRIVE.. COVER FOUR.. SCREWS CLUTCH CABLE ADJUSTMENT • Remove four screws from Rear Drive Cover. Lay aside cover and screws. • Place Clutch Lever in "DISENGAGED" position • The Cable should be under slight tension but should not pull the Clutch Lever more than 1/8" away from the Switch Body. NOTE: If the Plunger extends more than 1/8" out from the switch body, the cable tension is too tight and the Engine will not start. TO INCREASE CABLE TENSION • Place Blade Clu

FORM NO. 49464 (5/04) CAUTION: Read Rules for Safe Operation and Instructions Carefully • Safety • Assembly • Operation • Maintenance • Parts the fastest way to purchase parts Agri-Fab. TABLE OF CONTENTS SAFETY RULES ...................................................... 3,4 SAFETY AND OPERATIONAL DECALS ................ 5,6 HARDWARE CHART .................................................. 7 ASSEMBLY ............................................................ 8-11 OPERATION.....................