2. Locate the top of the belt idler assembly where the clutch cable (item 55) is secured in place. A properly tensioned belt should stretch the idler spring (located next to the idler pulley) between 1/4" -3/8" when the clutch bail (item 54) is held in the drive position. 3. Using a 1/2" wrench loosen the two nuts that secure the cable (item 55) in place. 4. TO INCREASE belt tension adjust these two nuts so that the cable (item 55) is secured in place with an additional 1/4" of the threaded adju

NOTE: Engage the clutch bail to use the front wheel drive to aid in turning the unit. TRANSPORT: Be sure to lift the tine engagement lever (tine out of the ground) before transporting away from the work area. HANDLING & TRANSPORTING CAUTION: This unit is heavy. It requires at least two people to lift it. REMOVE: The aerator is equiped with a removable rear weight. Remove the weight when loading and unloading the unit. The weight can be removed by rotating the locking tabs on the weight mounting

Label Warning Unit Weight Part No.360188 BEFORE STARTING, MAKE SURE: TINE DEPTH CONTROL BAIL IS IN UP POSITION. TO START, MOVE ENGINE STOP SWITCH TO "ON" AND PULL ROPE. NOTE: IT MAY BE NECESSARY TO USE THE ENGINE CHOKE IF ENGINE IS COLD. PUSH FORWARD ON TINE LIFT HANDLE TO ENGAGE TINES IN GROUND. PUSH FORWARD ON OPERATOR’S BAIL TO ENGAGE DRIVE AND START AERATING. DURING OPERATION PUSHING DOWN ON OPERATOR’S HANDLE WILL MAXIMIZE CORING DEPTH. RELEASE BAIL TO STOP UNIT. NOTE: ENGINE WILL CONTINUE T

OF USE TO PROLONG THE LIFE OF BELTS. Check brake puck Check parking brake Check tire pressure NOTE: infl ate to mfr.’s specifi cation as shown on tire side-wall Part No. 520141 Form No. F061604A 17.1 CABLE ADJUSTMENTS Brake Adjustment The brake control cable is spring loaded and requires no adjustment; however, the transaxle brake is adjustable. When the mower is in neutral and can be pushed by hand without depressing the brake lever, the transaxle brake needs adjustment. Using a . inch wrench t

1. Disconnect spark plug wire. 2. Remove the deck belt cover. 3. Support front of unit to allow access to underside of the machine near the engine. Note: Unit is heavy. Be sure support is adequate to prevent personal injury. 4. Observe the orientation of the belt fi ngers (Item 71) under the engine. 5. Remove the 4 engine mount bolts (Item 48) 6. Remove the left and right belt fi ngers (These fi ngers are interchangeable). 7. Observe the orientation of the belt fi nger (Item 90) on idler (Item 9

F112003A 33" TRIPLE BLADE MOWER COMMERCIAL Page 1 of 20 Operator Owner's Manual Thank You f o r S e l e c t i n g 1 3 Specifi cations The Powerful Self-Propelled Billy Goat Mower UNIT SIZE: OVERALL LENGTH - 57"(1.45 m) OVERALL WIDTH - 43" (1.09 m) OVERALL HEIGHT - 47" (1.19 m) FM3300IN ,FM3300INE, FM3300INB ,FM3300INEB FM3300IN FM3300INE FM3300INB FM3300INEB Engine: HP 13.0 HP (9.7 kW) 13.0 HP (9.7 kW) 13.0 HP (9.7 kW) 13.0 HP (9.7 kW) Engine:Type B&S INTEK OHV B&S INTEK OHV B&S INTEK OHV B&S IN

P/N 520144 Grass Catcher Kit Easily convert your mower to bag grass and leaves. P/N 520142 Transaxle Guard Kit To protect the transaxle from accidental contact from concrete curbs or other hazards. P/N 520155 Part No 520187 Form No F071406A 1 FM Owner’s Manual ABOUT THIS MANUAL THANK YOU for purchasing a BILLY GOAT ® FM Mower. Your new machine has been carefully designed and manufactured to provide years of reliable and productive service. This manual provides complete operating and maintenance

(2.8 L) 3.0 qt. (2.8 L) Engine: Oil Cap. 1.5 qt. (1.4 L) 1.5 qt. (1.4 L) Weight: Unit 267 # (121 Kg) 277 # (126 Kg) Weight: Shipping 343# (156Kq) 353# (160Kq) 2 Accessories Mulching Kit P/N 520144 Reduces lawn clippings to fine nutrient-rich par- ticles that filter down to the soil. Grass Catcher Kit P/N 520142 Easily convert your mower to bag grass and leaves. Transaxle Guard Kit P/N 520155 To protect the transaxle from accidental contact from concrete curbs or other hazards. Part No. 520188 Pa

Running the deck out of level will result in poor cut quality and increased belt wear. Fig. 2 Part No 510267 Form No F031607A 9 HW Owner’s Manual PROPULSION This unit is self-propelled, and is controlled by a lever control. To engage the wheel drive, pull up and squeeze it against operator's handle. The drive is disengaged by releasing this lever.(See Fig. 3 & 3.1) GROUND SPEED can be varied by selecting a higher or lower gear using the gearshift lever on top of the handle (See Fig. 4). Under mo

Move equipment away from spill until gasoline has completely evaporated. DO NOT operate engine without a muffler. Inspect muffler periodically and replace if necessary. If equipped with muffler deflector, inspect deflector periodically and replace if necessary. DO NOT operate engine with grass, leaves, or other combustible material near the muffler. DO NOT touch muffler, cylinder or cooling fins while engine is running. Contact with hot surfaces may cause severe burns. DO NOT operate equipment w