03021 LOWER CHUTE ATTACHING STRAPS PARTS IDENTIFICATION UPPER CHUTE CHUTE LATCH FULL BAG INDICATOR LOWER CHUTE GRASS CATCHER CONTAINERS COVER ASSEMBLY UNPACKING INSTRUCTIONS • Remove all parts and packing materials from carton. • Check carton contents against list. Be sure all parts are there. CARTON CONTENTS: (3) Container Tops (3) Container Bottoms (1) Upper Chute (1) Lower Chute (1) Support Assembly (1) Cover Assembly 5 1 BAGGER SUPPORT ASSEMBLY (See Fig. 1) 1. Slide fl anges of support assem

Do not use a nozzle lock-open device. • If fuel is spilled on clothing, change clothing immediately. • Never overfill fuel tank. Replace gas cap and tighten securely. GENERAL SERVICE • Never operate machine in a closed are. • Keep all nuts and bolts tight to be sure the equipment is in safe working condition. • Never tamper with safety devices. Check their proper operation regularly. • Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage and remove any fuel- s

ALIGNMENT MARKS 02085 COVER SEAL FIG. 3 7 SUPPORT POST (See Fig. 4) Use Hardware - - GROUP "C" CAUTION: Container sup port is spring loaded and locked to the cover. Handle cover assembly carefully so as not to unlatch the cover from the container support. 1. Rotate cover assembly onto its side as shown. 2. Assemble support post to container support with the three (3) carriage bolts and locknuts. Tighten securely. 02091 LOCKNUTS CARRIAGE BOLTS SUPPORT POST FIG. 4 5 5 MOUNTING TO TRACTOR (See Fig.

• If the grass catcher fails to pick up cut grass or leaves, it is an indication that clogging has occurred in the system or that the grass catcher containers are full. Usually this is indicated by the stopped movement of the full bagger indicator. a. Disengage blades, shift into neutral, en ga ge the parking brake and stop the engine. -Raise seat. Unlatch and raise cover. -Slide out containers and dispose of clip pings . -Replace containers, close cover, and latch. b. Unlatch chutes and check f

From backside of drawbar place reinforcement plate so that weld screws go through holes in left side of drawbar. Place support tube over weld screws and assemble flat washer, lockwasher, and wing nut as shown Do not tighten at this time. 4. Discard remaining hex bolts and locknuts in hardware GROUP "A". REINFORCEMENT UPPER CORNER RIBS LOCK WING NUTS 02352 LANCED TABS SELF TAPPING SHOULDER PLATE SUPPORT TUBE FLAT WASHERS WASHERS BOLTS TOWARD BOTTOM FIG. 1B DRAWBAR WITHOUT UPPER CORNER RIBS - STY

gauge wheel bracket. 5 CAUTION: Do not remove defl ector shield from mower. Raise and hold shield when attaching lower chute and allow it to rest on chute while in operation. WARNING Donotoperatemowerunless containeris properlyisnstalled.Containeris subjecttowearanddetierioration.Checkbagfrequently.Replacewhen cracked ordamaged.Useonlya recommendedreplacementcontainer. WARNING Donotoperatemowerunless containeris properlyisnstalled.Containeris subjecttowearanddetierioration.Checkbag frequently.Re

5 END CAP COVER ASSEMBLY SUPPORT POST MOUNTING BRACKET LANCED TABS BRACKET SUPPORT PIN RETAINER SPRING MOUNTING TO TRACTOR (See Fig. 5) Use Hardware - - GROUP "D" NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting assembly to tractor. 1. Raise seat on tractor to allow assembly to be mounted. 2. With cover closed, lift assembly and place support post inside mounting bracket. Allow assembly to rest on lanced tabs of mounting bracket. 3. Line up holes

S Wear hearing protection. S Never start or run inside a closed room or building. Breathing exhaust fumes can kill. S Keep handles free of oil and fuel. S Keep hands and feet away from cutting area. S Never direct discharge of material toward bystanders nor allow anyone near the area of operation. Use care in directing discharge to avoid glass enclosures, automobiles, and the like. FUEL SAFETY (for gas powerheads) S Mix and pour fuel outdoors. S Keep away from sparks or flames. S Use a container

3) NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting cover assembly to tractor. 1. Position cover assembly on ground behind tractor. 2. Lift and rotate cover to align cover brackets with support assembly tubes. 3. Slide cover assembly down onto the support tubes. FIG. 3 03024 COVER ASSEMBLY SUPPORT ASSEMBLY ASSEMBLY 02543 HANG SUPPORT ASSEMBLY ON REAR DRAWBAR (See Fig. 2) Determine the correct support assembly for your tractor. The support assembl

Always wear safety glasses or eye shields be fore starting your trac tor and while mow ing. We recommend wide vision safety mask for over the spec tacles or stan dard safety glasses. UNPACKING INSTRUCTIONS • Remove all parts and packing materials from carton. • Foldflaps to inside of carton and turn carton upsidedown on floor of work area. To protect grass catcher cover during assembly place cover upsidedown on overturned carton. • Check carton contents against list. Be sure all parts are there.