Évaluations - 5, GPA: 3.8
(
)
)
|
Facilité d'utilisation
45-02181 26" LEAF/LAWNSWEEPER Safety Assembly Operating Maintenance Repair Parts CAUTION: Read Rules for Safe Operation and Instructions Carefully thefastest way to purchase parts PRINTED IN USA FORM NO. 40261 (4/24/07) SAFETY RULES Remember, any equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when using this equipment. CAUTION: VEHICLE BRAKING AND STABILITY MAY BE AFFECTED WITH THE ADDITION OF AN ACCESSORY OR AN ATTACHMENT. BE AWARE OF CHANGING CONDITIONS ON SLOPES. LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS — ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED. Do not allow anyone to operate the sweeper without proper instructions. Do not permit children to operate sweeper. Eye protection should be worn while operating sweeper. Do not push or tow sweeper too close to a fire. Do not attempt to remove wire or string wrapped around brush while brush is rotating. Operate sweeper at reduced speed on rough terrain, in ditches and on hillsides to prevent tipping and loss of control. Stay alert for holes or other hidden hazards. This sweeper is not meant for street or highway use. Watch for traffic when sweeping near roadways. Keep all nuts, bolts and screws tight to be sure equipment is in safe working condition. Sweeper should be stopped and inspected for damage after striking a foreign object and damage should be repaired before operating the equipment. Follow maintenance instructions as outlined in this manual. CARTON CONTENTS 1. Sweeper Housing Assembly 2. Hopper Bag 3. Upper Handle 4. Lower Handle Leg Stand (2) 5. Short Bag Rod 6. Long Bag Rod HARDWARE PACK (NOT SHOWN FULL SIZE) ASSEMBLY INSTRUCTIONS TOOLS REQUIRED FOR ASSEMBLY (1) Phillips Screwdriver (1) Adjustable Wrench (1) 7/16" Open End or Box Wrench 1. Assemble the two Handle Leg Stand Tubes to the Sweeper Housing, using two hex bolts 1/4-20 x 1-1/4" long, flat washers and 1/4-20 hex lock nuts, per handle. See figure 1. Only hand tighten at this time. 2. Assemble the Upper Handle Tube over the Handle Leg Stand Tubes. See figure 2. Align holes in handle and assemble the Bag Rod Clips to the handle as shown and fasten with curved head bolts and hex lock nuts. Ref. Description Qty. No. A Hex Bolt, 1/4-20 x 1-1/4" 4 B Flat Washers 1/4" I.D. 4 C Hex Lock Nuts 1/4-20 8 D Bag Rod Clips 4 E Curved Head Bolts 1/4-20 x 1" 4 F Palnut 1/4" 2 G Plastic Caps (for bag rods) 2 H Plastic Caps (for leg stands) 2 FIGURE 1 FIGURE 2 3. Now tighten the four bolts from step 1. 4. Assemble a bag rod clip to the inside of each lower handle tube using a curved head bolt secured down against the clip using a 1/4" lock nut. The open end of the clips should face towards the sweeper housing. See figure 3. 5. Slide the long bag rod (28-1/2" long) through the stiched bag flap on the top of the hopper bag as shown in figure 4. 6. Slide the short bag rod (25-1/2" long) through the stiched bag flap on the bottom of the hopper bag as shown in figure 4. 7. Assemble the two plastic rod caps to the rod ends of the bottom bag rod. Assemble two Palnuts to the ends of the top bag rod. See figure 5. 8. Assemble the two plastic caps 3/4" x 7/8" onto the ends of the leg stands as shown in figure 6. FIGURE 5 FIGURE 3 FIGURE 6 FIGURE 4 9. Place the upper hopper bag and bag rod into the bag rod clips on the hopper handle. See figure 7. 10. Place the lower hopper bag and bag rod into the opening on the sweeper housing. See figure 8. 11. Hook the elastic straps on the bag flaps under the bag rod clips on the lower handle tubes as shown in figure 9. FIGURE 7 FIGURE 9 OPERATION Take care when operating your sweeper. Operating your sweeper according to these instructions will help prevent damage and prolong the life of your sweeper. BRUSH HEIGHT ADJUSTMENT To adjust your sweeper brushes to the best operating height, loosen the hand knob and slide the height adjustment tube down to raise or up to lower the brushes. Best adjustment is when brushes are set 1/2" down into the grass. Always mow grass to even height before sweeping. See figure 10. FIGURE 8 FIGURE 10 DUMPING OF SWEEPER To dump sweeper hopper bag, simply tip the sweeper forward or lift off the complete hopper bag frame. Always dump hopper after each use. Damp or wet grass and leaves will cause damage to hopper if stored for long periods of time. WHEEL GEARS/PAWL SERVICE IMPORTANT: Do not remove both wheels at the same time to avoid mixing parts. (The R.H. and L.H. ratchet gears are not interchangeable.) Make notes on the position of washers and snap rings during disassembly. 1. Remove only one wheel from the sweeper. 2. Remove the retaining rings and washers which hold the ratchet gear onto the brush shaft. 3. Remove the gear by sliding it off the brush shaft. (Look for the drive pin, which may fall out of the brush shaft when the ratchet gear is removed. 4. To reassemble, insert the drive pin through t...