Log:
Évaluations - 4, GPA: 4 ( )

Instructions Lasko, Modèle 2084537

Fabricant : Lasko
Taille : 317.59 kb
Nom Fichier : 3151G.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


(Figure 4) (Align Groove on blade hub with Pin on motor shaft. Figure 4A) Blade 1. Tilt Fan Head back. Place Plastic Rear Grill on Motor. (Figure 1) Figure 4 Motor Pin Plastic Rear Grill Fan Head Groove Figure 1 Figure 4A 2. Align tab of Plastic Rear Grill with groove on top of front Motor cover.(Figure 2) Plastic Rear Grill Motor Figure 2 2084537 7 Rev. F 10/09 2084537 2 Rev. F 10/09 REPLACEMENT PARTS LIST ASSEMBLY KEY 12" OSC 16" OSC DESCRIPTION 1 2011212 2011200M Rear Grill 2098060 2098061 Parts Bag*: 2 2010359 2010359 Plastic Nut (Large) 3 2010058 2010059 Spinner 4 2010380L 2010380L Ornament 5 2096531I 2096529I Front Grill 6 2010008 2011013 Blade 7 2010710 2010710 Motor Cover (Front w/Threads) 8 2010661 2010661 Motor Cover (Rear) 9 02030062GL 02030066GL Motor 10 02090040 02090040 Screw Motor Cover (1) 11 2010119 2010119 Oscillation Knob 12 02090060 02090060 #7 x .080 PPH Type B Screw (2) 13 07091657 07091657 Threaded Spindle 2010263S 2010263S Neck Assembly **: 14 2010251 2010251 Neck Piece Bearing 15 2010276 2010276 Oscillation Link 16 2090140 2090140 Link Screw (2) 17 2060090 2060090 Elevation Washer 18 02090585 02090585 Elevation Spring 19 2010252S 2010252S Neck Piece 20 02090051 02090051 Neck Screw 21 2060071 2060071 Elevation Range Plate 22 02090033 02090033 Hex Nut 23 02090521 02090521 Elevation Shaft 24 02010110A 02010110A Small Adjustment Knob 25 02010109A 02010109A Large Adjustment Knob 26 2010533 2010533 Stand 27 2009224 2009224 Knob 28 02055087 02055087 Switch 29 2010415 2010415 Rubber Feet (4) 30 02065457 02065458 Stand Ornament 31 02090038 02090038 Screw #8 x 9/16 PPH Type 25 32 2010343 2010343 Bottom Plate (Plastic) 33 2060012 2060012 Bottom Plate (Metal) 34 2091145 2091145 Screw #8 x 1.5 Type A POH 35 7091854 7091854 Crimp Connect 36 02050013WB 02050013WB Power Supply Cord w/Plug 37 2084537 2084537 Instruction Sheet (Not Shown) 5. To secure Blade, screw Spinner onto Shaft Counter Clockwise until tight on Blade hub. (Figure 5) 7. With Fan Head tilted back and centered, align Ornament of Front Grill so it is horizontal. Insert bottom of Front Grill into Rear Grill. Tabs at the bottom of Rear Grill should be between two wires of Front Grill. Snap Front Grill into the Rear Grill beginning at the top and working down both sides. (Figure 7) 11 10 16" Fan Spinner 9 12" Fan Spinner 8 Snaps 7 Snaps Figure 5 12 13 16 Ornament Tab Tab 6. Install Ornament into Metal Front Grill. Insert Tabs into rectanglar Slots. Snap into place. (Figure 6) 14 Figure 7 15 17 21 18 19 20 25 Tab 23 22 Slot Ornament Side View 26 Figure 6 27 24 28 36 35 30 29 34 32 33 31 * Parts 2-4 ordered as a Bagged Assembly ** Parts 14-21 ordered as an Assembly 1 6 2 3 (16") 4 5 3 (12") 2084537 3 2084537 Rev. F 10/09 6 Rev. F 10/09 OPERATION MAINTENANCE CONVERTING FROM TABLE FAN TO WALL MOUNTED FAN (Grills and blade removed for clarity) OSCILLATION: Push down oscillation knob on motor housing to make fan head move from side to side. (Figures 8 and 9) WARNING: ALWAYS UNPLUG CORD BEFORE CLEANING OR DISASSEMBLING. WARNING: DO NOT IMMERSE FAN IN WATER! CLEANING: IMPORTANT! DO NOT immerse electrical parts in water! Disassembled grills may be immersed to be cleaned with a mild detergent and water. Wipe all other parts with soft cloth moistened with water and mild detergent only. DRY ALL PARTS COMPLETELY BEFORE REASSEMBLING. After any maintenance or servicing, completely reassemble unit as described in this instruction manual before reconnecting to the power supply. CAUTION: Do not use gasoline, benzine, thinner, harsh cleaners, etc. as they will damage the Fan. NEVER use ALCOHOL OR SOLVENTS. SERVICING: All other servicing, with the exception of general user maintenance, should be performed by an authorized service representative. Call 1-800-233-0268, Monday through Friday, between the hours of 8:00 a.m.and 5:00 p.m. EST for the location of your nearest service center. LUBRICATION: Motor is permanently lubricated. MOTOR HOUSING Down: Oscillate Up: Stationary NECK LARGE ADJUSTMENT KNOB (For minor adjustments) SMALL ADJUSTMENT KNOB STAND Figure 8 Figure 9 SPEED: Control fan speed with Speed Knob. (Figure 10) 3 - High Speed 2 - Medium Speed 1 - Low Speed 1. UNPLUG FAN FROM OUTLET. 2. Remove the Small and Large Adjustment Knobs. 1/8" Speed Knob Figure 10 TILTING: This Fan is equipped with a multi-angle Fan Head for Whole-Room Air Circulation. Follow the steps below to properly adjust the "tilt angle" of your Fan. 1. Place one hand just under the Fan Neck. 2. Place your other hand on top of Fan. 3. Gently push or pull the Fan Head until it is in the desired position. 3. Tilt Motor Housing all the way back. 4. Reinstall Small Adjustment Knob and tighten. 5. Reinstall Large Adjustment Knob. 6. Install two #8 x 1 1/4" Wood Screws (not provided), using Template below, leaving 1/8" between Screwheads and wall. 7. Mount Fan over Screws using Slotted Holes on Bottom Plate. NOTE: TO ADJUST HEAD VERTICALLY - Loosen Large Adjustment Knob, set Motor Housing...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories