A beep indicates the initiation of the Self-Test sequence. Self-Test will check battery capacity and perform five functional test sequences as described in the digital display Appendix. The last green LED and the message SELF-TEST PASS on the display indicate a successful test. If any of the individual tests fail during Self-Test, there will be two beeps and a red LED flash, with the name of the test that failed and an “X” on the display. Self-Test will discontinue at that point. See Appendix D

At the same time the 406 MHz signal is activated, a 121.5 MHz signal is turned on. The 121.5 MHz signal is used by SAR to home in on the beacon as they approach it. The 406 MHz signal is detected by multiple satellites and from that information the location of the beacon can be calculated. This data alone is sufficient for SAR to find persons or ships in distress in a reasonable timeframe. However, as a further enhancement, some beacons have a GPS engine onboard. This feature allows the beacon t

During the warranty period ACR Electronics, Inc. will repair or, at its option, replace the unit at no cost to you for labor, materials and return transportation from ACR. For further assistance, please contact our Technical Service Department at ACR Electronics, Inc., 5757 Ravenswood Road, Fort Lauderdale, FL 33312-6645. Email: service@acrelectronics.com, Fax: +1 (954) 983-5087, Telephone: +1 (954) 981- 3333. This warranty does not apply if the product has been damaged by accident or misuse, or

2766.6 ETSI Type Approved to ETS 300 152 Y1-03-0167 Rev. B ACR Electronics, Inc. 5757 Ravenswood Road Fort Lauderdale, Fl 33312 Tel : +1(954) 981-3333 Fax: +1 (954) 983-5087 Email: Info@acrelectronics.com * * * WARNING * * * THIS TRANSMITTER IS AUTHORIZED FOR USE ONLY DURING SITUATIONS OF GRAVE AND IMMINENT DANGER DELIBERATE MISUSE MAY INCUR A SEVERE PENALTY Foreword: Congratulations and thank you! You have just purchased the finest Class B personal EPIRB available on the market. Other brands me

Antenna is spring loaded and deploys rapidly. The release trigger holds the antenna down at the beacon’s side in the stowed position. When the beacon is switched to the “ON” position the antenna will spring into an upright position. The antenna should then be extended to its full length for optimum transmission performance. The beacon should be operated in an area free of obstructions. 3.2 MANUAL ACTIVATION The beacon is manually activated. Manually activating the beacon requires movement of the

Use the antennas supplied with this kit. The VHF antenna supplied for use with the Nauticast™-B is omni-directional, vertically polarized with unity gain (0 dB) and a band width sufficient to maintain VSWR <1.5 over the frequency range 156–163 MHz. As a minimum the 3dB bandwidth will cover the two AIS channels and the DCS channel. The antenna is also suitable for marine shipboard applications (index of protection, ruggedness, means of mounting, etc.). If you elect to not use the antenna supplied

C Manual Footer In the United States WARNING: It is a violation of the rules of the Federal Communications Commission to input an MMSI that has not been properly assigned to the end user, or to otherwise input any inaccurate data in this device. WARNING: This product is a supplemental navigation tool only! The user assumes all responsibility associated with the use of this device and safe navigation. It is important to understand that all vessels may not be equipped with AIS transponders and the

If the internet is not accessible to you, complete the enclosed registration form. Do not confuse this with the ACR Electronics warranty card. Mail with the pre-addressed, postage paid envelope to: NOAA SARSAT Beacon Registration NSOF, E/SP3 4231 Suitland Road Suitland, MD 20746 C. Faxing your registration is also acceptable. Fax the registration form to fax # +1 (301) 817-4565. Note that the information you provide on the registration form is used only for rescue purposes. Complete and send the

Figure 5 - Belt Clip . 5.1 Multi-Function Belt Clip The MicrOFix™ comes standard with a multi-function belt clip. To install the clip, simply align the bottom tabs on the clip with the insert holes located on the bottom of the beacon. Snap the clip in place by pressing the top of the clip so that the two top tabs engage in the two insert holes on the top of the beacon (see figure 5). To remove the clip, push up and back on the top tabs one at a time to disengage the clip from the beacon. The Mic

A OWNER VESSEL RADIO CALL SIGN UIN # CAUTION: Before proceeding to install, test or use your new ACR Electronics’ product, please read this Product Support Manual in its entirety. If you have questions regarding the contents of the manual, please contact our Technical Service Department at ACR Electronics, Inc., Telephone +1 (954) 981- 3333. Please be ready to provide the technician with the page number you wish to discuss. If you have a question that is not covered in the manual, please visit o