Évaluations - 5, GPA: 4.8
(
)
)
|
Facilité d'utilisation
Apply the Serial Number Sticker Place the serial number sticker from the kit on the outside of the cabinet in the upper left- hand corner, as shown by the arrow in the picture below. This completes the cabinet conversion. Proceed to the next section to verify proper operation and calibrate the joystick. © 2004 GLOBAL VR®, INC. 040-0050-01 Rev. A 10/29/2004 Page 25 of 48 Section 3 – Power ON and Test the Cabinet Section 3 – Power ON and Test the Cabinet Before powering the cabinet ON for the first time, please verify the following: • AC power is correctly setup inside the cabinet. • The DC power supply is correctly setup to provide power to the Jamma Conversion Board. • All connections are correct and secure. Once you have verified that all hardware is installed correctly, power ON the cabinet and verify that the game starts and runs properly, and that all controls function properly. Use the Player Control Test (see page 33) from the Operator Menu to verify that the joystick and buttons are working properly. Insert some coins and verify that the coin inputs are working properly. Start a game (see page 35) and verify that it plays properly. Run the Joystick Calibration Utility The Joystick Calibration Utility adjusts the software to match the joystick motion. Run the Joystick Calibration Utility whenever you replace the joystick or install game software on the system. 1. Insert the Joystick Calibration Utility CD in the computer CD-drive. The CD will run automatically. You will see a series of processing screens, followed by windows telling you to move the joystick in certain ways. 2. Move the joystick as instructed by the onscreen prompts. 3. Ignore the windows that refer to "Throttle" and "Rudder." Simply click the trigger to exit from these windows. gvrSX™ Conversion System Manual Page 26 of 48 040-0050-01 Rev. A 10/29/2004 Section 3 – Power ON and Test the Cabinet Adjust the Universal Video Converter (UVC) The Universal Video Converter (UVC) is designed to work with most EGA and CGA arcade monitors. When you power the cabinet up for the first time, you may need to adjust the settings on the UVC board to match the monitor. To correctly set up the UVC, you must know the resolution and Horizontal and Vertical Sync setup of the monitor. Depending on your cabinet, the J7 video output of the UVC can be connected directly to the video input on the monitor, or to J4 on the Jamma Conversion Board to route the signals through the Jamma harness to the monitor. Table 3. UVC DIP Switch Settings SW 1 & 2 Both normally ON. SW 3 Output Resolution ON: CGA = 640 x 200 @ 15.72 KHz OFF: EGA = 640 x 384 @ 24.5 KHz SW 4 and 5 Input Resolution Both normally ON to auto detect the video resolution. SW 6 H Sync Signal Normally ON. Changing the H Sync signal will move the entire picture left or right. Change this setting if you find the picture is too far to one side and you cannot adjust it using the monitor remote control panel. SW 7 V Sync Signal Normally ON. Changing the V Sync signal will move the entire image up or down. Change this setting if you find the image is too far up or down on the monitor, and you cannot adjust it using the monitor remote control panel. SW 8 H-V / Composite Sync ON: Composite sync, for monitors with one composite (combined) sync line (most CGA monitors). OFF: For monitors with two separate H and V sync lines (most EGA monitors). Change this setting only if you have no picture on your monitor. © 2004 GLOBAL VR®, INC. 040-0050-01 Rev. A 10/29/2004 Page 27 of 48 Section 4 – Using the Game Operator Menu Section 4 – Using the Game Operator Menu All gvrSX™ game audits, game adjustments, and control diagnostics are options of the Game Operator Menu. Press the Operator Button behind the coin mech door in the cabinet to activate the Game Operator Menu. The screen shown below is the first screen that you will see after pressing the Operator button. The Options menu is displayed on the left side of the screen, and the settings for the selected option are displayed on the right. You do not see a mouse pointer when using the joystick or trackball to navigate the Game Operators Menu; instead, each option or menu button will highlight in yellow when it is ready to be selected. Setting Game Options and Resets Once in the Operator Menu, use the Joystick and Trigger and Buttons to navigate and set up the game software, as described below: 1. Use the Joystick to navigate and highlight an item in the Options list. 2. Press the Trigger Button to open the menu for the selected Option. 3. Use the Joystick to move between the items in the window, and to scroll through the available settings for each item. 4. To change a setting, use the joystick to scroll to the desired setting, and then press the Trigger Button to set it. gvrSX™ Conversion System Manual Page 28 of 48 040-0050-01 Rev. A 10/29/2004 Section 4 – Using the Game Operator Menu Machine Menu The Machine menu is the default screen displayed when you press the Opera...
Ce manuel est également adapté pour les modèles :Consoles de jeux - 040-0050-01 (1.19 mb)