Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
Make sure the Ramp is completely open. Make sure the tailgate the ramp will sit on, is 1. dry and clean. Sit the tongue (angled lip) of the Ramp on the tailgate. Stretch the Safety Chain on each 2. Ramp being used up into the inside of the truck bed; attach the hook on each Safety Chain to a secure attachment point on the inside of the truck bed. WARNING! SAFETY CHAINS MUST BE connected to secure attachment points within the truck bed able to withstand the pulling force of loading. They must also be taut enough to prevent the ramp from coming off the vehicle being loaded. Pull the loading ramp back until the chains are tight. The entire tongue portion of the 3. ramps must fit onto the tailgate; If not, adjust the Safety Chains (12) accordingly or shorter chains must be used. REV 07l Chain Adjustment: Remove the bolt and washer that hold the safety chain to the ramp. 4. Reinsert the bolt through a link that will shorten the chain so the loading ramp can not be pulled backwards by the ATV’s rear tire. Make sure that the bolt is properly tightened and the washer prevents the bolt from slipping through the chain link. Adjust the other chain to equal length. 4- Wheel ATV Loading WARNING! THIS tri-Fold RAMP IS FOR USE WITH 2 or 4-WHEELED Dirt Bikes and • ATV’S ONLY. Do not use this ramp to load 3-wheeled vehicles. Do not use this tri-fold ramp to load any vehicle that weighs • more than 1000 lb. Be sure the tires of the ATV being loaded are not wider than THE • width of the ramps. DO NOT USE this tri-fold ramp to load any vehicle that is carrying • gear on its racks. Do not use this ramp if the tailgate on the vehicle being loaded • is higher than half the ramp’s length. WARNING! All persons not involved in the loading process must stand clear of the loading Ramp and truck. Make sure no pets are nearby. Only use a winch (Not Provided) to load the 4-Wheel ATV. This is the safest way to load a 4-WHEEL ATV.1. The winch and mounting/connection points must all have appropriate capacity to 2. pull the ATV up the ramp safely. Winch Setup:3. ATV-Mounted:a. Unwind cable from the winch and attach it to a secure mounting location on the truck, at the same height as the winch will be after the ATV has been loaded. Truck Mounted:b. Attach the cable to the bottom front part of the frame. While operating the winch, stand back and to the side of the ATV, with the vehicle between 4. you and the winch cable. WARNING! BE SURE THE 4-WHEELED ATV IS CENTERED ON RAMPS.5. Operate the winch to slowly load the ATV onto the vehicle.6. Once load is in truck bed, be sure to set the ATV’s brake & securely tie down ATV. 7. Remove the ramp, fold it up and secure it within the truck bed using the Safety Chains and Hooks (12). Caution! Contact between the tongue (angled lip) of the ramp and the tailgate of the vehicle may result in damage to the vehicle’s body finish. 4- Wheel ATV Unloading WARNING! THIS RAMP IS FOR USE WITH 2 or 4-WHEELED ATV’S ONLY. Do not use • this ramp to Unload 3-wheeled vehicles. Do not use this ramp to unload any vehicle that weighs more • than 1000 lb. Do not use this ramp to unload any vehicle that is wider than THE • ramps, adjust the ramps by moving the ATV close to the Hauling vehicle and adjusting the width before putting any weight on the tri-fold ramps. DO NOT USE this ramp to unload any vehicle that is carrying gear • on its racks. Do not use this ramp if the tailgate on the vehicle being unloaded • is higher than half the ramp’s length. WARNING! All persons not involved in the unloading process must stand clear of the loading Ramp and truck. WARNING! Riding an ATV while Unloading is dangerous and should not be attempted. Have a qualified adult assistant monitor the Ramp tongue for slippage on the tailgate.1. Setup the ramp on the truck bed as explained under “Operation”, on page 4. Remove 2. all tie down straps and securing equipment from the ATV. WARNING! BE SURE THE 4-WHEELED ATV IS CENTERED ON RAMP. While staying off the ATV, start the engine, disengage the parking brake, put the transmis3. sion into reverse, and make sure the wheels are in a straight line with the ramp. While holding the brake, position yourself on the truck bed in front of the ATV. Release the brake and push on the ATV to get it started down the ramp. Allow the ATV 4. to roll down naturally, do not attempt to steer it or apply the brakes. If it stops while on the ramp, gently give it throttle to back it off the ramp. 2-WHEEL BIKE LOADING Never attempt to load any dirt bike or other 2-wheel motor bike alone. Always have a 1. qualified adult to assist. Line up the 2-Wheel bike with one of the Tri-Fold Ramp sections.2. With one person pushing the bike slowly up the Ramp, a helper should be in the bed 3. of the hauling vehicle both to guide and to apply the brake if it is necessary to stop the bike while it is on the ramp. Always have one person with a hand on the bike hand brake for safety. Once the person inside the truck bed has hold of the ...
Ce manuel est également adapté pour les modèles :Fauteuils roulants - 96514 (397.57 kb)